manualshive.com logo in svg

ComAp ID-FLX-Lite-PC, Global Manual

Share
Download
ComAp ID-FLX-Lite-PC Global Manual Download Page 117

InteliDrive Lite - 1.2.1 Global guide

117

Setpoint group

Basic setting 2

Related FW

1.2.1

Range [units]

0 - 10 [-]

Default value

0

Force value

Step

1

Comm object

11475

Related applications

Config level

Standard

Setpoint visibility

Always

Description

The second RPM (RPM-BI3 value) can be measured in limited frequency range 1 to 50Hz on Binary input 3.

The RPM-BI3 value indicates RPM calculated from BI3 frequency and Basic settings: GearTeeth3 setpoint.

The RPM-BI3 value =0 below 1Hz and =### over 50Hz.

Configure BI Type = Not used and change the name according the function for RPM-BI3 measuring

Note:

The RPM-BI3 measuring is switched off when Basic setting: GearTeethBI3 = 0. In this case BI3

operates as standard Binary input.

Gear Teeth BI3

6

back to List of setpoints

Setpoint group

Basic Settings 2

Related FW

1.2.1

Range [units]

[-]

Default value

PICKUP

Force value

Step

[-]

Comm object

12142

Related applications

Config level

Standard

Setpoint visibility

Always

Description

Switch from where the RPM is measured. When source is Analog input the converted value is going to be in

RPM range – see example below.

RPM Source

6

back to List of setpoints

Summary of Contents for ID-FLX-Lite-PC




















































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands