manualshive.com logo in svg

ComAp ID-FLX-Lite-PC, Global Manual

Share
Download
ComAp ID-FLX-Lite-PC Global Manual Download Page 11

InteliDrive Lite - 1.2.1 Global guide

11

Communication - via communication modules e.g. IL-NT-GPRS, IB-Lite, IL-NT-S-USB and PC tools

WebServer, WebSupervisor, InteliMonitor etc.

Process logic - active control of engine, history log, configuration-no programming

2.3 Configurability and monitoring

InteliDrive IPC is used as configuration, monitoring and controlling tool LiteEdit software. For simple

configuration, monitoring and controlling can be used InteliMonitor.

2.3.1 Open connection from LiteEdit

PC tool LiteEdit is used for monitoring, programming and configuration of ID-FLX-Lite controllers.

1. Go to menu Connection and select the type of connection you desire.

Image 2.1 LiteEdit - connection menu

2. Enter controller address and further information depending on the selected connection type.

Note:

For direct connection enter controller address

Summary of Contents for ID-FLX-Lite-PC




















































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands