manualshive.com logo in svg

COMAC ULTRA 85BS, Manual Use And Maintenance, Page: 15 / 31

Share
Download
COMAC ULTRA 85BS Manual Use And Maintenance Download Page 15

 

15

MACHINE PREPARATION 

 

 

1 

2 

10.  ASSEMBLING THE BRUSHES

 

 

1.  Connect the battery connector 
2.  Turn the key to the ON position 
3.  Use the lever to raise the base 
4.  Turn the key to the OFF position and remove it from the panel 

(carrying out the brush assembly operation with the power supply 
connected may cause injuries to the hands) 

3 

4 

 

 

5.  With the base up, release the side bar from its support  
6.  Loosen the knob (1) and take out the movable brush support plate (2) 
 
 
 

This operation must be carried out using gloves to 
protect your hands 

 

 

7.  Insert the brush in the tunnel until it is placed on the driving hub 
8.  Check the inclination of the bristles on the front cylindrical brush (3) 

and the rear brush (4) 

9.  Insert the idle hub of the movable plate in the brush 
10. Hook the plate to the tunnel and tighten the knob 
11. Repeat the process for the other movable plate 
 

 

 

1 

2 

3 

4 

Summary of Contents for ULTRA 85BS
































Reviews:

No comments