COMAC CS50 B Use And Maintenance Manual Download Page 21

 

 

 

21

EC DECLARATION OF CONFORMITY 

 

The undersigned manufacturer: 

COMAC S.p.A. 

Via Maestri del Lavoro n.13 

37050 Santa Maria di Zevio (VR) 

declares under its sole responsibility that the product 

 

SWEEPING MACHINES 

 
complies with the requirements of the following Directives: 
 

 

2006/42/EC: Machinery Directive 

 

2004/108/EC: Electromagnetic Compatibility Directive 

 

2000/14/EC: Directive by the European Parliament and Council date 8th May, 2000. Noise emission by machines and equipment for outdoor use. 

 

Falling into the category of roadsweeper as defined in Annex 46 of Directive 2000/14/EC of the European Parliament and the Council, is subject to noise 
marking only. 
Conformity assessment was carried out as set out in Annex III.B.46 of the said directive.  
 

MODEL 

LwA   [dB(A)] 

LwA, guaranteed [dB(A)] 

FS50 B 

81.74 

85 

FS50 BT 

81.74 

85 

FS50 H 

89.3 

93 

FS50 HT 

89.3 

93 

 
They also comply with the following standards: 

 

EN 60335-1: Household and similar electrical appliances - Safety. Part 1: Generic norms 

 

EN 60335-2-72: Household and similar electrical appliances. Part 2: Specific norms for automatic machines for floor treatment for commercial and 
industrial use 

 

EN 12100-1: Machine safety - Fundamental concepts, fundamental principles of design - Part 1: Basic terminology and methodology 

 

EN 12100-2: Machine safety - Fundamental concepts, fundamental principles of design - Part 2:  Technical principles 

 

EN 61000-6-2: Electromagnetic compatibility (EMC) - Part 6-2: Generic norms – Immunity for industrial environments. 

 

EN 61000-6-3: Electromagnetic compatibility (EMC) - Part 6-3: Generic norms — Standard emission for residential, commercial and light-industrial 
environments 

 

EN 62233: Household and similar electrical appliances - Electromagnetic fields Methods for evaluation and measurement 

 
The person authorised to compile the technical file: 
 
Sig. Giancarlo Ruffo 
Via Maestri del Lavoro, 13 
37050 Santa maria di Zevio (VR) - ITALY 

 

Santa Maria di Zevio, 04/10/2010 
 
 

 

 

 

 

 

 

 

 

 

        COMAC S.p.A. 
Legal representative 
Giancarlo Ruffo 
 
 
 

 

COMAC spa  

Via Maestri del Lavoro, 13 - 37050 S.Maria di Zevio (Verona) Italy 

Tel. +39 045 8774222 – Fax +39 045 8750303 - E-mail:

[email protected]

 o 

[email protected]

  - 

www.

comac.it

 

 

Summary of Contents for CS50 B






















Reviews: