COMAC ANTEA 50 B, Use And Maintenance Manual

Page: 29 / 44

EMPTYING THE DEBRIS HOPPER (65 BTS double brush versions)
To empty the debris hopper, proceed as follows:
1. Take the device to the dedicated maintenance area.
2. Take all necessary steps to ensure that the device is in a safe condition (see “ MACHINE SAFETY ”).
CAUTION : these operations must be carried out using protective gloves to avoid any possible
contact with the edges or tips of metal objects.
3. Stand on the left side of the appliance.
4. Remove the left side splash guard support (1) ( Fig. 1 ).
5. Extract the debris hopper (2) from the brush head body ( Fig. 2 ).
N.B. : To do this, use the moulded handle on the lower part of the debris hopper.
6. Empty the inside of the debris hopper using a spatula to remove any dirt residues if necessary.
N.B. : the place designated for this operation must comply with current environmental protection
regulations.
7. Repeat the operations in reverse order to reassemble all the parts.
1 2
1 2
CLEANING THE SQUEEGEE BODY
The careful cleaning of the whole vacuum unit ensures better drying and cleaning of the floor as well as a
longer vacuum motor life. To carry out the cleaning of the squeegee body, proceed as follows:
1. Take the device to the dedicated maintenance area.
2. Take all necessary steps to ensure that the device is in a safe condition (see “ MACHINE SAFETY ”).
N.B. : these operations must be carried out using protective gloves to avoid any possible contact
with the edges or tips of metal objects.
3. Remove the vacuum hose (1) from the vacuum nozzle (2) on the squeegee body ( Fig. 1 ).
4. Completely unscrew the knobs (3) on the squeegee body pre-assembly (
Fig. 2
).
5. Remove the squeegee body from the slits in the squeegee connector ( Fig. 3 ).
6. Thoroughly clean the squeegee body vacuum chamber (4) with a jet of water, and then with a damp
cloth ( Fig. 4 ).
N.B. : the place designated for this operation must comply with current environmental protection
regulations.
7. Thoroughly clean the squeegee body front rubber blade (5) with a jet of water, and then with a damp
cloth (
Fig. 5
).
8. Thoroughly clean the squeegee body's rear rubber blade (6) with a jet of water, and then with a
damp cloth ( Fig. 6 ).
9. Unscrew the knobs (7) that fix the vacuum nozzle (3) to the squeegee body ( Fig. 7 ).
10. Remove the vacuum nozzle (3) from the squeegee body ( Fig. 7 ).
11. Thoroughly clean the vacuum nozzle (3) with a jet of water, and then with a damp cloth.
12. Also clean the support surface on the squeegee unit ( Fig. 8 ).
13. Position the vacuum nozzle (3) on the squeegee unit and fix it in place by means of the knobs (8).
14. For refitting the squeegee unit read the paragraph “ FITTING THE SQUEEGEE UNIT ”.
3
1 3
2
2 1
6
6
5
4
4 5
3
7
7 8
To clean the squeegee body with the spray gun, for versions with the SST system, proceed as follows:
1. Take the device to the dedicated maintenance area.
2. Lift the brush head body and press the “BRUSH HEAD CONTROL” button (1) on the control panel
( Fig. 1 ).
3. Raise the squeegee unit and turn the squeegee control lever (2) in the direction of the arrow in
( Fig. 2 ). The lever is located on the back of the device.
CAUTION : these operations must be carried out using protective gloves to avoid any possible
contact with the edges or tips of metal objects.
4. Remove the vacuum hose (3) from the vacuum nozzle (4) on the squeegee body ( Fig. 3 ).
5. Completely unscrew the knobs (5) on the squeegee body pre-assembly ( Fig. 4 ).
6. Remove the squeegee unit from the slits in the squeegee connector ( Fig. 5 ).
7. Remove the spray gun kit from the storage compartment ( Fig. 6 ).
8. Connect the male quick-coupler (6) on the spiral hose (7) to the female quick-coupler (8) on the front
of the appliance ( Fig. 7 ).
9. Connect the male quick-coupler (9) on spray gun (10) to the female quick-coupler (11) on the spiral
hose (7) ( Fig. 8 ).
10. Activate the spray gun kit by pressing the button (12) on the steering column ( Fig. 9 ).
CAUTION : when using the optional tank cleaning kit, you are advised to always wear goggles to
avoid any risk of serious injury to your eyes.
N.B. : before activating the optional tank cleaning kit, check the level indicator (13) to see how
much solution there is in the solution tank ( Fig. 10 ).
11. Start the delivery of detergent solution by pressing the lever (14) on the spray gun ( Fig. 11 ).
N.B. : To adjust the solution jet coming out of the spray gun turn the knob (15) on the accessory
itself ( Fig. 12 ).
12. Thoroughly clean the vacuum chamber of the squeegee body, first with a jet of water and then with
a damp cloth.
N.B. : the place designated for this operation must comply with current environmental protection
regulations.
13. Thoroughly clean the vacuum chamber (16) of the squeegee body with a jet of detergent solution and
then with a damp cloth (Fig. 13) .
14. Thoroughly clean the front rubber blade (17) of the squeegee body with a jet of detergent solution
and then with a damp cloth ( Fig. 14 ).
15. Thoroughly clean the rear rubber blade (18) of the squeegee body with a jet of detergent solution and
then with a damp cloth (
Fig. 15
).
16. Unscrew the knobs (19) that fix the vacuum nozzle (20) to the squeegee body ( Fig. 16 ).
17. Remove the vacuum nozzle (20) from the squeegee body ( Fig. 16 ).
18. Thoroughly clean the vacuum nozzle (20) with a jet of detergent solution and then with a damp cloth.
19. Also clean the support surface on the squeegee unit ( Fig. 17 ).
20. Place the vacuum nozzle (20) on the squeegee body and fix it in place using the knobs (19).
3
4
3
1
1
2
2
5
5
4 6
7 8 9
7
6
11 12
8
9
10
13
14
15
10 11 12
18
15
17
16
13 14
29