manualshive.com logo in svg

Colop digital e-mark create, Operating And Maintenance Manual, Page: 47 / 60

Share
Download
Colop digital e-mark create Operating And Maintenance Manual Download Page 47

 

 

   

e-mark create marking device

 

Chapter 6 Maintenance 

CODI Standard 1.0

 

 

47/60 

Operating and Maintenance Manual 

 

 

If the app is on and there is a WIFI connection with the device, the charging process is also displayed in the 

app (

see chapter 5.3

)

.

 

 

6. 

Disconnect the charger when fully charged.  

 

WARNING!

 

Hazard from rechargeable batteries (short-circuit, overheating, fire).

  

- Do not expose lithium batteries to heat, cold or water (do not leave in direct sunlight 

or charge or store outdoors). 

- Do not (forcibly) open or expose to large impacts or shocks. 

- Only use charging systems as recommended by the manufacturer. 

- The manufacturer's safety instructions must be complied with throughout the entire 

disposal process. 

- Battery contacts (outside the device) must not come into contact with metallic objects 

such as coins or keys, to prevent a short circuit. 

- The marking device and/or rechargeable battery must never get wet. 

- Burning batteries can cause blow-outs, causing a battery to be blown away. Battery 

fires give off extremely thick, particularly toxic smoke. 

- Following extended periods in storage or before taking to a collection point, the poles 

on  lithium  rechargeable  batteries  should  be  covered  with  adhesive  tape  to  prevent 

short  circuits.  Maximum  possible  storage,  e.g.  in  the  original  packaging  and  quick 

deposit in a collection point are recommended. 

- Visually damaged, overheated or blown out batteries must not be recycled and must 

not be stored in the house, flat or garage. 

 

 

NOTICE

 

Do  not  charge  the  battery  longer  than  needed  to  protect  the  battery  and  to  prevent 

impairment of the print quality of the ink cartridge. 

 

 

NOTICE

 

Charging is only possible using the mains adapter and charger. Charging via the USB 

connection is not possible. 

 

 
 
6.2  Changing the ink cartridge 

An empty ink cartridge is indicated on the Light Guide as a red light and in online mode with the symbol 

 in the 

app. Change the ink cartridge as follows: 

1.  Open and remove the e-mark create cover. 

Summary of Contents for digital e-mark create





























































Reviews:

No comments