Colop digital e-mark create Operating And Maintenance Manual Download Page 44

Page: 44 / 60

e-mark create marking device

Chapter 5 Operation

CODI Standard 1.0

44/60

Operating and Maintenance Manual

5.8 USB cable connection

The e-mark create can also be connected via a USB cable to a computer. Connect the USB cable to the e-mark

create and computer.

Fig. 36: USB connection

The

computer

software

can

downloaded

free

charge

from

the

COLOP

homepage

(

https://getemarkcreateapp.colop.com/

5.9 Storage

Store the product in a dry place. When storing the e-mark create, always place in the docking station to prevent

drying out the print head. Store batteries only when charged.

When stored for extended periods, keep it in the original packaging or in the additionally available transport case to

protect it. It is recommended to activate the e-mark create at least once a month to prevent the print head from

completely drying out. Batteries should be charged, if required. Complete the self-cleaning process and make a test

imprint. In the event the test imprint quality is poor, complete a manual cleaning cycle (

see chapter 5.5

)

NOTICE

Always place the e-mark create in the docking station during storage. It is

recommended to activate the e-mark create at least once a month and to complete the

automatic cleaning process (or manual cleaning process, if required).

Summary of Contents for digital e-mark create





























































Search results

Summary of Contents for digital e-mark create

Reviews:

Related manuals for digital e-mark create

Brands by name

Popular brands

Colop digital e-mark create, Operating And Maintenance Manual

Search results

Summary of Contents for digital e-mark create

Reviews:

Related manuals for digital e-mark create

Brands by name

Popular brands