manualshive.com logo in svg

Colop digital e-mark create, Operating And Maintenance Manual, Page: 20 / 60

Share
Download
Colop digital e-mark create Operating And Maintenance Manual Download Page 20

 

 

   

e-mark create marking device

 

Chapter 3 Description 

CODI Standard 1.0

 

 

20/60 

Operating and Maintenance Manual 

 

 

3.4  Technical specifications and dimensions 

 

Technical specifications of the e-mark create 

Weight 

224.5 g (approx. 450 g incl. packaging) 

Dimensions L x W x H 

111.2 x 76.5 x 72.7 mm 

Rechargeable battery (3 cells, each 3.7 V) 

11.1 V Li-Ion with min. 600 mAh 

Power consumption while operation with battery 
supply 

5-6 W 

Power consumption while battery is charging 
(WIFI activated) 

15 V, 400 mA 

Power consumption in sleep mode 

10-12 mW 

WIFI interface 

WIFI IEEE 802.11bgn 

USB interface 

Micro USB 

Optimum print speed 

4 in/s 

Maximum print speed 

11 ¾ in/s 

Print quality 

600 dpi 

Protection class 

III, Extra low voltage 

Mains connection charger 

100-240 V, 50/60 Hz 

Print head 3-colour (cyan, magenta, yellow) 

COLOP 3-colour Ink Cartridge C2P06AE 

Storage temperature range 

-40 °C to 60 °C 

Operating temperature range 

15 °C to 35 °C 

Non-Operating humidity range 

20 to 80 % 

Print on absorbent surfaces such as 

Plain paper, cardboard, fabric, wood, cork, dry wall, high-

gloss paper, photo paper 

 

Surfaces: 

The e-mark create can print directly onto a variety of absorbent flat surfaces including standard paper, cardboard, 

fabric, wood, cork, dry wall, high-gloss paper, photo paper and other surfaces with special coatings. 

 

 

 

Summary of Contents for digital e-mark create





























































Reviews:

No comments