manualshive.com logo in svg

Colop digital e-mark create, Operating And Maintenance Manual, Page: 16 / 60

Share
Download
Colop digital e-mark create Operating And Maintenance Manual Download Page 16

 

 

   

e-mark create marking device

 

Chapter 3 Description 

CODI Standard 1.0

 

 

16/60 

Operating and Maintenance Manual 

 

 

3 

D

ESCRIPTION

 

The following chapter presents an overview of parts, assembly and function including technical specifications and 

product components. 

 

 

3.1  Scope of supply 

 

Fig. 2: Package content 

 

The packaging of the e-mark create contains the marking device with rechargeable battery (1), docking station (2), 

charger and cable (3), ink cartridge (4) and the Quick Setup Guide (5).  

The marking device comprises the housing with top section that can be opened (access to compartment for battery 

and ink cartridge), an on/off switch on the underside, a micro USB port, an LED light guide, sliding wheels on the 

underside for stable movement, 3 magnets for secure docking, contacts for charging on the docking station, a light 

sensor for position guiding, a WIFI module. 

The docking station comprises a charging socket for the power adapter, contacts for charging the e-mark create, 

rubber lips and flap to prevent the ink cartridge from drying out, an opening to access the on/off switch on the e-mark 

create when docked, non-slip pads and an extendible wiper to wipe the underside of the ink cartridge. 

The rechargeable battery is supplied with a plastic cover on the contacts. This prevents short-circuiting the contacts 

during transport. This cover must be removed before use. 

The ink cartridge is packaged separately and must be inserted before use.  

 

 

 

NOTICE 

Even if the illustrations in this document correspond to the e-mark (an additional 

product within the COLOP product range) and not the e-mark create, they are equally 

valid for the respective function as for the e-mark create. 

 5 

Summary of Contents for digital e-mark create





























































Reviews:

No comments