Coherent Solutions BERTPXIe-1003 User Manual Download Page 100

Page: 100 / 102

PXIe Platform Bit Error Rate Tester

BERTPXIe-1003/1005

Coherent Solutions Ltd.

Version

1.00

Liability

Coherent Solutions shall not be liable for damages resulting from the use of the product, nor

shall be responsible for any failure in the performance of other items to which the product is

connected or the operation of any system of which the product may be a part.

Coherent Solutions shall not be liable for damages resulting from improper usage,

transportation or unauthorized modification of the product, its accompanying accessories and

software.

Exclusions

Coherent Solutions reserves the right to make changes in the design or construction of any of

its products at any time without incurring obligation to make any changes whatsoever on

units purchased. Accessories, including but not limited to fuses, pilot lamps, batteries and

universal interfaces (EUI) used with Coherent Solutions products are not covered by this

warranty.

This warranty excludes failure resulting from: improper use or installation, normal wear and

tear, accident, abuse, neglect, fire, water, lightning or other acts of nature, causes external to

the product or other factors beyond the control of Coherent Solutions.

Certification

Coherent Solutions certifies that this equipment met its published specifications at the time of

shipment from the factory.

Service and Repairs

Coherent Solutions commits to providing product service and repair for five years following

the date of purchase.

MPORTANT

Coherent Solutions will charge a fee for replacing optical connectors

that were damaged due to misuse or insufficient cleaning.

Summary of Contents for BERTPXIe-1003







































































































Search results

Summary of Contents for BERTPXIe-1003

Reviews:

Brands by name

Popular brands

Coherent Solutions BERTPXIe-1003, User Manual

Search results

Summary of Contents for BERTPXIe-1003

Reviews:

Brands by name

Popular brands