Cognex In-Sight 7600 Reference Manual Download

Page: 90 / 113

High-Speed Output Wiring

To connect to an NPN-compatible PLC input, connect one of the vision system's high-speed outputs directly to the PLC

input. When enabled, the output pulls the PLC input down to less than 3VDC.

To connect to a PNP-compatible PLC input, connect one of the vision system's high-speed outputs directly to the PLC

input. When enabled, the output pulls the PLC input up to greater than 21VDC.

To connect the high-speed outputs to a relay, LED or similar load, connect the negative side of the load to the output and

the positive side to +24VDC. When the output switches on, the negative side of the load is pulled down to less than

3VDC, and 24VDC appears across the load. Use a protection diode for a large inductive load, with the anode connected

to the output and the cathode connected to +24VDC.

Specifications

Summary of Contents for In-Sight 7600


















































































































Search results

Summary of Contents for In-Sight 7600

Reviews:

Related manuals for In-Sight 7600

Brands by name

Popular brands

Cognex In-Sight 7600, Reference Manual

Search results

Summary of Contents for In-Sight 7600

Reviews:

Related manuals for In-Sight 7600

Brands by name

Popular brands