Cognex In-Sight 7600 Reference Manual Download

Page: 20 / 113

External Lights

External lights can be connected to the vision system's LIGHT connector using the External Light cable.

Note

The vision system supports connecting an integrated illumination accessory to the vision system's faceplate

and connecting an external light to the vision system's LIGHT connector, but does not support using both

lighting devices simultaneously.

If daisy-chaining multiple Cognex IVSL-YLW2X-xxx or IVSL-YLW300-xxx external lights:

The lights must be powered externally by a separate power supply.

A Cognex control cable (CCB-FOV25-MAL-012) can be used to connect the vision system’s LIGHT

connector to the external light and a Cognex power cable (IVSL-5PM12-5) can be used to connect

the light to the separate power supply. Only the power and ground wires from the Cognex power

cable (IVSL-5PM12-5) should be connected to the remote power supply.

If using a Cognex IVSL-LX520-xxx external light:

The lights must be powered externally by a separate power supply.

A Cognex control cable (CCB-FOV25-MAL-012) can be used to connect the vision system’s LIGHT

connector to the external light and a Cognex power cable (IVSL-5PM12-5) can be used to connect

the light to the separate power supply. Only the power and ground wires from the Cognex power

cable (IVSL-5PM12-5) should be connected to the remote power supply.

The following cables must not be used with IVSL-LX520-xxx external lights: IVSL-5PM12-J300,

IVSL-5PM12-J500 and IVS-5PM12-J1000, IVSL-5PM12-J2000.

The vision system supports Cognex IVSL-YL300-xx external lights with the following External Light cables:

IVSL-M12-NSB-300, IVSL-M12-NSB-1000 and IVSL-M12-NSB-2000.

Accessory

Part Number

Supported External Light Cables

Accessory Image

Brick light, narrow blue

IVSL-ODDM-S75-470 IVSL-5PM12-J300

IVSL-5PM12-J500
IVSL-5PM12-J1000
IVSL-5PM12-J2000

Brick light, narrow red

IVSL-ODDM-S75-625 IVSL-5PM12-J300

IVSL-5PM12-J500
IVSL-5PM12-J1000
IVSL-5PM12-J2000

Introduction

Summary of Contents for In-Sight 7600


















































































































Search results

Summary of Contents for In-Sight 7600

Reviews:

Related manuals for In-Sight 7600

Brands by name

Popular brands

Cognex In-Sight 7600, Reference Manual

Search results

Summary of Contents for In-Sight 7600

Reviews:

Related manuals for In-Sight 7600

Brands by name

Popular brands