Cognex DataMan 333L Reference Manual Download Page 9

Page: 9 / 70

Diffuse lens cover, red illumination (assembled), ESD safe

DM300-DLCOV-RE-ESD

Red LED high power integrated light, 10.3 mm lens

(Risk Group Red LED Exempt acc. IEC 62471, Risk Group Green LED
Aimer Exempt acc. IEC 62471)

DM360-HPIL-RE

Polarized red LED high power integrated light, ESD safe,
10.3 mm lens

(Risk Group Red LED Exempt acc. IEC 62471, Risk Group Green LED
Aimer Exempt acc. IEC 62471)

DM360-HPIL-RE-P

White LED high power integrated light, 10.3 mm lens

(Risk Group white LED low risk acc. IEC 62471, Risk Group Green LED
Aimer Exempt acc. IEC 62471)

DM360-HPIL-WHI

Red LED high power integrated light, 24 mm lens

(Risk Group Red LED Exempt acc. IEC 62471)

DMLT-HPIL-RE

Polarized red LED high power integrated light, 24 mm lens

(Risk Group Green LED Aimer Exempt acc. IEC 62471)

DMLT-HPIL-RE-P

White LED high power integrated light, 24 mm lens

(Risk Group white LED low risk acc. IEC 62471, Risk Group Green LED
Aimer Exempt acc. IEC 62471)

DMLT-HPIL-WHI

C-Mount cover for C-Mount lenses

DM300-CMCOV

Short C-Mount cover for C-Mount lenses

DM300-CMCOV-SH

External Lights (Red LED)

Ring light

CLRR-R7030G1CLR

Back light

CLRB-F100100G1

Coaxial (DOAL) light

CLRO-K5050G1

Spot light

CLRS-P14G1

Dark-field light

CLRD-D120G1

Getting Started

Summary of Contents for DataMan 333L






































































Search results

Summary of Contents for DataMan 333L

Reviews:

Brands by name

Popular brands

Cognex DataMan 333L, Reference Manual

Search results

Summary of Contents for DataMan 333L

Reviews:

Brands by name

Popular brands