Cognex 3D-A5000 Series Hardware Reference Manual Download

Page: 6 / 19

PC Requirements

Any PC you use with a 3D-A5000 sensor must meet certain minimum requirements. Cognex also makes

recommendations for some components.

Components

Requirement

CPU

Minimum:

4th generation Intel® Core™ i5 Processor with 4 cores

Recommended:

8th generation Intel Core i7 Processor with four physical cores (8 logical cores)

Intel Xeon E5 Processor with six physical cores (12 logical cores)

Operating System

Windows 10 Pro 64-bit

GPU (mandatory)

Minimum:

NVIDIA GeForce GTX 1070

Recommended:

NVIDIA GeForce GTX 1080

Cognex also supports:

NVIDIA GeForce GTX 1070 Ti

NVIDIA GeForce GTX 1080 Ti

NVIDIA Graphics Driver

Minimum:

Version 387

Recommended:

Version 396 or later

10 Gigabit Ethernet Adapter

Recommended:

Chelsio T520-BT

https://www.chelsio.com/nic/unified-wire-adapters/t520-bt/

Refer to the Chelsio documentation for correct installation procedures

Download the latest driver software for the Chelsio T520-BT:

https://service.chelsio.com/downloads/Microsoft/

Recommended Package Type: exe

RAM

Minimum: 8GB

Recommended:16GB

Ethernet Cable

Recommended: Cat6a

Power Supply

Required power supply depends on all system components. For typical setups (no
additional hardware components [single GPU, single CPU]):

600W power supply for GTX 1070 and GTX 1070 Ti

700W power supply for GTX 1080 and GT 1080 Ti

Supported Sensors

Refer to the following table for details on the 3D-A5000 sensors supported by this VisionPro release:

Cognex 3D-A5000 Sensors

Summary of Contents for 3D-A5000 Series




















Search results

Summary of Contents for 3D-A5000 Series

Reviews:

Related manuals for 3D-A5000 Series

Brands by name

Popular brands

Cognex 3D-A5000 Series, Hardware Reference Manual

Search results

Summary of Contents for 3D-A5000 Series

Reviews:

Related manuals for 3D-A5000 Series

Brands by name

Popular brands