Coemar ISPOT 575 EB Instruction Manual Download Page 24

Page: 24 / 26

The display panel of the

ISPOT 575 EB

allows for the electronic alignment of the projector’s motors in the optical system. This pro-

cedure is performed by

coemar

at the factory. It may be useful to perform this procedure in the case of internal components being

replaced.
Altering the factory settings may radically alter the functioning of the projector. Carefully read all of the following prior to attempt-
ing any changes.

electronic calibration

1) Press the

menu

button.

2) Press the

button until the display shows

RESE

(for reset).

3) Press the

enter

and

menu

buttons simultaneously and hold for at least

30"

. The motors of the unit will perform a reset and the

display will show

–- –- –- –-

for some few seconds, indicating that you have entered the electronic calibration mode:

Note

: Simultaneously pressing the

and

–

buttons will return the calibration value to the default value of 128.

press together to acces motors

electronic calibration procedure

enter

menu

RESE

PNAL

pan alignment

pan movement alignment

TLAL

tilt alignment

tilt movement alignment

SH R

shutter alignment

alignment of shutter right part

SH L

shutter alignment

alignment of shutter left part

C1AL

colour wheel alignment

colour wheel 1 alignment (the one nearest to the lamp)

C2AL

colour wheel alignment

colour wheel 2 alignment

FOAL

focus alignment

focusing lens alignment

G1AL

gobo wheel 1 alignment

gobo wheel 1 alignment (the one nearest to the lamp)

G2AL

gobo wheel 2 alignment

gobo wheel 2 alignment

GR1

gobos alignment

rotating gobos alignment on gobo wheel 1
(the one nearest to the lamp)

GR2

gobos alignment

rotating gobos alignment on gobo wheel 2

PRAL

prisms alignment

rotating prisms alignment

IRAL

iris alignment

iris diaphragm alignment

LEAL

lenses alignment

step zoom lenses alignment

END

end

to end the electronic motor calibration procedure and to record it

0120

0140

0120

0130

0127

0121

0140

0127

0125

0135

0132

es.

0128

A001

0128

☞

enter

☞

enter

☞

enter

☞

enter

☞

enter

☞

enter

☞

enter

☞

enter

☞

enter

☞

enter

☞

enter

☞

enter

☞

enter

☞

enter

☞

enter

☞

enter

☞

enter

☞

enter

☞

enter

☞

enter

☞

enter

☞

enter

☞

enter

☞

enter

☞

enter

☞

enter

☞

enter

☞

enter

0127

☞

AOO1

☞

menu

FUNC

☞

Attention!

Electronic calibration is only possible if the projector is receiving

DMX 512

signal.

Attention!

This section is reserved only for technical and specialist personnel.

23. Electronic motor alignment

English

Summary of Contents for ISPOT 575 EB



























Search results

Summary of Contents for ISPOT 575 EB

Reviews:

Coemar ISPOT 575 EB, Instruction Manual, Page: 24 / 26

Search results

Summary of Contents for ISPOT 575 EB

Reviews: