background image

29 LTD HD LE

Operating Instructions 
for your Cobra 29 LTD HD LE

Edition

CB Radio

The Citizens Band lies between the shortwave
broadcast and 10-meter Amateur radio  bands,
and was established by law in 1949. The Class D
two-way communications service was opened in
1959. (CB also includes a Class A citizens band 
and Class C remote control frequencies.)

FCC Regulations

FCC regulations permit only “transmissions”
(one party to another) rather than “broadcasts”
(to a wide audience). Thus, advertising is not
allowed on CB Channels because that is
“broadcasting.”

FCC Warnings 

All transmitter adjustments other than those 
supplied by the manufacturer as front panel 
operating controls, must be made by, or under 
the supervision of, the holder of an FCC-issued
general Radio-Telephone Operator’s License.

Replacement or substitution of transistors, regular
diodes or other parts of a unique nature, with
parts other than those recommended by Cobra,
may cause violation of the technical regulations 
of Part 95 of the FCC Rules, or violation of Type
Acceptance requirements of Part 2 of the Rules.

You should read and understand Part 95 (included
with this unit) of the FCC Rules and Regulations,
before operating your Cobra radio, even though
the FCC no longer requires you to obtain an
operator’s license.

What’s Included with Your 29 LTD HD LE

1.

CB transceiver

6.

DC power cord

2.

Microphone

7.

FCC rules

3.

Transceiver bracket

1.

(not shown)

4.

Microphone bracket

5.

Operating Manual

29 LTD HD LE

Cobra Electronics Corporation
6500 West Cortland Street
Chicago, IL 60707 USA

©2002 Cobra Electronics Corporation
Printed in China

Part No. 480-053-P

Operating Instructions 
for your Cobra 29 LTD HD LE

Edition

CB Radio

The CB Story

A1

For technical assistance, please call our Automated Help Desk which can assist 

you by answering the most frequently asked questions about Cobra products.

(773) 889-3087 

24 hours a day, 7 days a week.

A Consumer Service Representative can be reached at 773.889.3087 

8:00 am - 6:00 pm, Monday through Friday, CST.

Technical assistance is also available on-line in the Frequently Asked Questions (FAQ) section

at www.cobra.com or by e-mail to [email protected]

If you think you need service call 773.889.3087

“If your product should require factory service please call Cobra first before sending your unit in.
This will ensure the fastest turn-around time on your repair.”

You may be asked to send your unit to the Cobra factory. It will be necessary to furnish the
following in order to have the product serviced and returned.

1. For Warranty Repair include some form of proof-of-purchase, such as a mechanical reproduction

or carbon or a sales receipt. If you send the original receipt it cannot be returned.

2. Send the entire product.

3. Enclose a description of what is happening with the unit. Include a typed or clearly print name

and address of where the unit is to be returned.

4. Pack unit securely to prevent damage in transit. If possible, use the original packing material.

5. Ship prepaid and insured by way of a traceable carrier such as United Parcel Service (UPS) or 

First Class Mail: to avoid loss in transit to: Cobra Factory Service, Cobra Electronics Corporation,
6500 West Cortland Street, Chicago, IL 60707 USA.

6. If the unit is in warranty, upon receipt of your unit it will either be repaired or exchanged

depending on the model. Please allow approximately 3 to 4 weeks before contacting us for 
status. If the unit is out of warranty a letter will automatically be sent informing you of the 
repair charge or replacement charge. If you have any questions, please call 773.889.3087 for
assistance.

If You Think You Need Service

3

2

4

5

1

All manuals and user guides at all-guides.com

all-guides.com

Summary of Contents for Harley-Davidson 29 LTD HD LE
























Reviews: