manualshive.com logo in svg

COBHAM 2201R, Reference Manual, Page: 66 / 295

Share
Download
COBHAM 2201R Reference Manual Download Page 66

2201R Mobile Tester  SCPI Reference Guide

Chapter 6 Status commands

47090/323

Copyright © 2016 Aeroflex Limited. All rights reserved.

66

:STATus:OPERation:NTRansition 

Syntax

:STATus:OPERation:NTRansition <int1>

Parameters

int1 is an integer. The minimum value for int1 is 0, the maximum value is 32767. The default value is 0.

Description

Sets the NTR mask of the General operation register group. This mask is ANDed with the up to 15 bits of the NTR 
transition filter of the general operation condition register to allow a reset (negative transition) of any bit (i.e. a 
transition from logic "1" to "0") to reach the general operation event register.
Notes 
- The default of this mask is 0 — that means that the mask does not allow any negative transition of the lower 15 
bits of the condition-type register to reach the event-type register.
- Bit 16 of the general operation condition register is not used.

Query

There is no query form of this command available.

Example

:STATus:OPERation:NTRansition 32767
This means that all of the negative transitions of the condition-type register are forwarded to the event-type register.

Summary of Contents for 2201R








































































































































































































































































































Reviews:

No comments