manualshive.com logo in svg

COBHAM 2201R, Reference Manual, Page: 59 / 295

Share
Download
COBHAM 2201R Reference Manual Download Page 59

2201R Mobile Tester  SCPI Reference Guide

Chapter 5 System commands

47090/323

Copyright © 2016 Aeroflex Limited. All rights reserved.

59

:SYSTem:COMMunicate:SERA:REMote 

Syntax

:SYSTem:COMMunicate:SERA:REMote <PredefExpr>

Parameters

PredefExpr can take on either of the following expressions: ON|OFF. Default is ON.

Description

Enables or disables remote control of the 2201R via the serial interface port COM 1.
Note: The remote control capability at COM 1 should be disabled prior to controlling external equipment (e.g. the 
Bluetooth Connectivity Test products) through this interface.

Query

Returns the current setting.

Example

:SYST:COMM:SERA:REM OFF
:SYST:COMM:SERA:REM?
Returns the following string: "OFF"

:SYSTem:COMMunicate:SERA:TERMinator 

Syntax

:SYSTem:COMMunicate:SERA:TERMinator <PredefExpr>

Parameters

PredefExpr can take on either of the following expressions: LF|CR|CRLF.

Description

The command defines the delimiter for SCPI control strings for the RS-232 interface.

Query

Reads and returns the current setting of the terminator used on the RS-232 interface.

Example

:SYST:COMM:SERA:TERM LF
:SYST:COMM:SERA:TERM?
Returns the following string: "LF"

Summary of Contents for 2201R








































































































































































































































































































Reviews:

No comments