manualshive.com logo in svg

COBHAM 2201R, Reference Manual, Page: 56 / 295

Share
Download
COBHAM 2201R Reference Manual Download Page 56

2201R Mobile Tester  SCPI Reference Guide

Chapter 5 System commands

47090/323

Copyright © 2016 Aeroflex Limited. All rights reserved.

56

:SYSTem:COMMunicate:TCPip:GATeway 

Syntax

:SYSTem:COMMunicate:TCPip:GATeway <string>

Parameters

string is a string only containing the default gateway address for the 2201R.

Description

This command sets the default gateway address of the 2201R. See section I/O Configuration for more details.

Query

Reads and returns the current setting of the gateway address as explained above.

Example

SYST:COMM:TCP:GAT "192.16.16.1" sets the gateway address to a defined value.

:SYSTem:COMMunicate:TCPip:PORT 

Syntax

:SYSTem:COMMunicate:TCPip:PORT <int>

Parameters

int defines the TCP/IP port address of the 2201R. The address must be in the range from 49152 to 65535.

Description

This command sets the port address on which the 2201R can be controlled via LAN. See section I/O Configuration 
for more details.

Query

Reads and returns the current setting of the port used by TCPIP as explained above.

Example

SYST:COMM:TCP:PORT 49200 sets the TCP/IP port address to its default.

Summary of Contents for 2201R








































































































































































































































































































Reviews:

No comments