manualshive.com logo in svg

COBHAM 2201R, Reference Manual, Page: 289 / 295

Share
Download
COBHAM 2201R Reference Manual Download Page 289

2201R Mobile Tester  SCPI Reference Guide

Chapter 11 Fetch commands

47090/323

Copyright © 2016 Aeroflex Limited. All rights reserved.

289

:FETCh:EGPRs:RFTX:ALL?

Syntax

:FETCh:EGPRs:RFTX:ALL?

Parameters

There are no parameters.

Description

There is solely a query form of this command available.

Query

The query form of this command returns the latest measurement result values of the :MEAS:EGPR[:ARR]:RFTX:ALL 
measurement. The string delivered back contains 17 measurement result values, separated with commas. The order 
and type of these measurement result values delivered back is as follows:
1. ERMS, the error vector magnitude rms-averaged over a burst. EVM is a relative value and shown as a percentage,
2. EPEAk, the maximum error vector magnitude within a burst. EVM is indicated per cent,
3. ENFTh, the error vector magnitude that is not exceeded by 95% of the symbols of a burst. The 95% EVM is shown 
in %,
4. EOFFset, the origin offset indicates the accuracy of the i/Q modulators DC setup; it is usually an undesired leakage 
produced due to a DC offset in the phones I/Q modulator. It is measured in dBc,
5. FREQuency, floating point real number representing the mobile’s frequency error,'
6. LENGth, floating point real number representing the length of the burst in microseconds,
7. UTIMe, floating point real number representing the timing error of the mobile under test in microseconds (taking 
the ordered timing advance into account),
8. POWer, floating point real number representing the mobile’s RF output power level in dBm,
9. TEMPlate boolean number. 0 indicates that the power-time template (PTT) was not violated by the last burst 
measured, while a 1 means that the burst did violate the PTT.
10...17. CORNer, eight floating point real numbers, representing the RF power level in dBm at eight pre-defined 
positions of a burst.

Example

:MEAS:EGPR:RFTX:ALL
:FETC:EGPR:RFTX:ALL?
This example returns the latest measurement result values for the 17 most important EGPRS RF TX measurements. 
The string delivered back in this example is:
"5.13,11.94,3,12,4.54,-2.22,557.0,0.1,11.22,0,-72.18, -61.91,-20.91,-0.05,-0.04,-17.97,-56.60,-73.95".

Summary of Contents for 2201R








































































































































































































































































































Reviews:

No comments