manualshive.com logo in svg

COBHAM 2201R, Reference Manual, Page: 242 / 295

Share
Download
COBHAM 2201R Reference Manual Download Page 242

2201R Mobile Tester  SCPI Reference Guide

Chapter 10 Measurement commands

47090/323

Copyright © 2016 Aeroflex Limited. All rights reserved.

242

:MEASure:GPRS:ARRay:RFRX:BER:CII 

Syntax

:MEASure:GPRS:ARRay:RFRX:BER:CII <int1>

Parameters

int1 is an integer.
The minimum value for int1 is 0, the maximum value is 100. The default value for int1 is 0.

Description

Performs the measurement of the (nonresidual) bit error ratio on the class II bits a specific number of times (set with 
the int1 parameter). To read out the entire measurement results array, use the :FETCh:GPRS:RFRX:BER:CII command.
Notes: 
The number of samples to be used for testing can be set, using the :CONF:GPRS:BER:COUNt command.

Query

The query form of this command performs the measurement the specified number of times (int1 parameter). As soon 
as all measurements have been completed, all measurement result values are returned in a string. The string delivered 
back contains int1 floating point real numbers, representing the bit error ratios.
The single measurement results are separated by commas.

Example

:MEASure:GPRS:ARRay:RFRX:BER:CII? 5
The string returned is: "1.4,1.4,1.5,1.7,1.3".

:MEASure:GPRS:ARRay:RFRX:BER:CRC 

Syntax

:MEASure:GPRS:ARRay:RFRX:BER:CRC <int1>

Parameters

int1 is an integer.
The minimum value for int1 is 0, the maximum value is 100. The default value for int1 is 0.

Description

- Performs the measurement of the (non-residual) bit error ratio on the class II bits a specific number of times (set 
with the int1 parameter). To read out the entire measurement results array, use the :FETCh:GPRS:RFRX:BER:CII 
command.
Notes: 
- The number of samples to be used for testing can be set using the :CONF:GPRS:BER:COUNt command.

Query

The query form of this command performs the measurement the specified number of times (int1 parameter). As soon 
as all measurements have been completed, all measurement result values are returned in a string. The string delivered 
back contains int1 floating point real numbers, representing the bit error ratios.
The single measurement results are separated by commas.

Example

:MEAS:GPRS:ARR:RFRX:BER:CRC? 5
The string returned in this example is: "1.4,1.4,1.5,1.7,1.3".

Summary of Contents for 2201R








































































































































































































































































































Reviews:

No comments