Home
/
COBHAM
/
2201R
/
Reference Manual

COBHAM 2201R, Reference Manual, Page: 135 / 295

Share

Page: 135 / 295

COBHAM 2201R Reference Manual Download Page 135

2201R Mobile Tester SCPI Reference Guide

Chapter 8 Configuration commands

47090/323

Copyright © 2016 Aeroflex Limited. All rights reserved.

135

:CONFigure:GPRS:TYPE

Syntax

:CONFigure:GPRS:TYPE <PredefExp>

Parameters

PredefExp is one of the following predefined expressions: GSM9001800|GSM9001900. Default is GSM9001800.

Description

Selects the type of GSM system to be used after the 2201R was brought into GSM call mode.
GSM9001800 makes the 2201R work as a test set for the GSM system types GSM 850/900 and GSM 1800.
GSM9001900 sets up the 2201R as a test set for the GSM system types GSM 850/900 and GSM 1900.
Notes
The main reason for this command to exist is the duplicate use of channels numbers. GSM 1800 and GSM 1900 use
the same channel numbers above channel number 511, but the related physical channels are in different frequency
bands.

Query

The query form of this command returns the current setting. The string delivered back contains one of the predefined
expressions as explained above.

Example

:CONFigure:GPRS:TYPE GSM9001900
:CONF:GPRS:TYPE?
Value returned: "GSM9001900".

:CONFigure:GPRS:SMS:MCLass

Syntax

:CONFigure:GPRS:SMS:MCLass <int1>

Parameters

int1 is an integer.
The minimum value for int1 is 0, the maximum value is 3. The default value for int1 is 0.

Description

This command allows to predefine the SMS data coding scheme message class.

Query

The query form of this command returns the current setting. The string delivered back contains one integer.

Example

:CONFigure:GPRS:SMS:MCLass 1
:CONF:GPRS:SMS:MCL?
Value returned in this example: "1"#

«
...
133
134
135
136
137
...
»

Summary of Contents for 2201R








































































































































































































































































































Reviews:

No comments