manualshive.com logo in svg

Cobalt Digital Inc 9902-2UDX-DI, Product Manual, Page: 90 / 108

Share
Download
Cobalt Digital Inc 9902-2UDX-DI Product Manual Download Page 90

3

9902-2UDX-DI Function Menu List and Descriptions

3-56

9902-2UDX-DI PRODUCT MANUAL

9902-2UDXDI-OM (V1.0)

Provides a global card operating status and allows a 
log download for factory engineering support. Also 
provides controls for selecting and loading card 
firmware upgrade files.

Networking controls provide dedicated card networking 
setup in conjunction with rear module Ethernet port.

• Log Status and Download Controls

Admin

• Log Status indicates overall card internal operating status.

• Download Log File allows a card operational log file to be saved to 

a host computer. This log file can be useful in case of a card error or 
in the case of an operational error or condition. The file can be 
submitted to Cobalt engineering for further analysis.

• Thermal Shutdown enable/disable allows the built-in thermal 

failover to be defeated. (Thermal shutdown is enabled by default).

CAUTION

The 9940-ACO FPGA is designed for a normal-range operating 
temperature around 85° C core temperature. Operation in severe 
conditions exceeding this limit for non-sustained usage are within 
device operating safe parameters, and can be allowed by setting 
this control to Disable. However, the disable (override) setting 
should be avoided under normal conditions to ensure maximum 
card protection. 

•  Card DashBoard Name Control

Allows card name In DashBoard to be changed as desired. Click return to 
engage change.

• Append to Product Name appends (or adds to) existing OEM 

name (for example, “9940-ACO Processing 1A”).

• Replace Product Name completely replaces the OEM name OEM 

name (for example, “Processing 1A”).

Note: DashBoard instance(s) may have to be refreshed before 

name change appears.

• Firmware Upgrade Controls

Firmware upgrade controls allow a selected firmware version (where 
multiple versions can be uploaded to the card’s internal memory) to 
invoke an upgrade to a selected version either instantly, or set to install 
on the next card reboot (thereby allowing card upgrade downtime to be 
controlled at a scheduled point in time).

Table 3-2

9902-2UDX-DI Function Menu List — continued

Summary of Contents for 9902-2UDX-DI













































































































Reviews:

No comments