GREAT BRITAIN • CUSTOMER SERVICE
tel. 020 8247 9300 e-mail [email protected] internet www.clasohlson.co.uk
postal 10 – 13 Market Place, Kingston Upon Thames, Surrey, KT1 1JZ
Ver
. 20170927
LED-Driver
Art.no 36-6063
Model A3848
Please read the entire instruction manual before using the product and
then save it for future reference. We reserve the right for any errors in
text or images and any necessary changes made to technical data. In
the event of technical problems or other queries, please contact our
Customer Services.
Safety
Warning:
Whenever installing any electrical fittings, basic safety precautions
should always be observed to avoid the risk of fire, electric shock and
personal injury.
Warning:
All light fittings must be installed in accordance with current
safety regulations to prevent life-threatening accidents. The installation
should only be performed by competent persons with the required
knowledge of electrical wiring. If in doubt, contact a qualified electrician.
• The product is intended for indoor use only.
• The product must not be modified or used for any other purpose
than that for which it has been designed.
• Make sure that the wires do not rub against sharp corners or edges.
• This is not a toy! Do not let children play with the product or be in
its immediate proximity without adult supervision.
• The product may not be used if any part is damaged. If so, it
should either be discarded or repaired by a qualified technician.
• Do not cover the product with anything that will hinder proper
ventilation, such as foil, paper, plastic, etc.
• The rating label containing the type designation must not be
removed or made illegible.
• The product is designed to supply power to 350 mA LED light
fittings with a total load of max 18 W.
Installation
Note:
Make sure that the 230 V power supply cable is disconnected
from the mains and is
NOT
live before beginning the installation.
1. Remove the screws holding the covers over the connections in
place and remove the covers.
2. Connect the input 230 V AC
to the terminal block,
attaching the blue wire to
N
and the black (or brown)
wire to
L
on the block.
3. Connect an output cable
to the LED driver. The black
wire should be connected
to the
−
terminal on
the LED driver and the red
wire to the
+
terminal.
4. The LED lights should be connected to the driver in series, see
the picture below. Max 6 LED downlights of the same type as
article no 36-1140 (3 V/350 mA) can be driven by the LED driver.
The example below shows 4 lights connected.
Note:
The LED lights must
only
be connected in series, as shown
above,
not
in parallel. Connecting the lights in parallel with damage
the LED driver. Make sure that the polarity of the connections on
the terminal block is correct.
5. Secure the wires in the strain reliefs on both sides.
6. Screw the covers back over the terminal blocks on the LED driver.
Both covers also serve as strain reliefs.
Note:
The strain reliefs are designed for H03VVH2-F cable.
Terminal block for incoming 230 V AC
Terminal block for 3–18 V/350 mA to the LED light/s
Responsible disposal
Specifications
•
Input
100–240 V AC, 50/60 Hz
•
Output
3–18 V DC, 350 mA
•
Power
18 W for LED downlights and other 350 mA LED lights
• For use with (H03VVH2-F) 0.5–1.0 mm² cable
• Non-dimmable
This symbol indicates that this product should not
be disposed of with general household waste. This
applies throughout the entire EU. In order to prevent
any harm to the environment or health hazards caused
by incorrect waste disposal, the product must be
handed in for recycling so that the material can be
disposed of in a responsible manner. When recycling
your product, take it to your local collection facility or
contact the place of purchase. They will ensure that
the product is disposed of in an environmentally sound
manner.