manualshive.com logo in svg

Cmsemicon BAT32G1 9 Series, User Manual

The Cmsemicon BAT32G1 9 Series is an innovative product designed for intuitive user experience. With its extensive features and functionalities, this device provides exceptional performance. To learn more about this product, you can easily download the free user manual from manualshive.com, where detailed instructions are available for hassle-free setup and operation.

Share
Download
background image

BAT32G1x9 user manual | Chapter 24 Enhanced DMA

 

www.mcu.com.cn

                                                                               

1026 / 1149

 

 

Rev.1.02

 

24.3.12 

DMAENi position register (DMSETi). 

 
This is the DMA

 

boot allowing the register DMAENi to set the position register, set the corresponding bit to 1 to 

set the corresponding position bit of DMAENi to 1.  

 

Figure 24-13 

Format of the DMAENi position register (DMSETi) (i=0~4). 

 

 

address: 40005018H (DMSET0) , 40005019H (DMSET1) ,  

4000501AH (DMSET2) , 4000501BH (DMSET3) ,  
4000501CH(DMSET4) 

after reset:00H 

R/W 

 

symbol

 

7 

6 

5 

4 

3 

2 

1 

0 

DMSETi 

DMSETi7 

DMSETi6 

DMSETi5 

DMSETi4 

DMSETi3 

DMSETi2 

DMSETi1 

DMSETi0 

 

 

DMSETin

 

The position register for DMAENin

 

0

 

No assertion is generated.

 

1

 

Set the bit n of DMCENi to 1

 

 

Note: i=0

～

4

，

n=0~7

 

 

24.3.13 

DMAENi reset register (DMCLRi). 

 
This is the reset register that DMA

 

initiates to allow register DMAENi, and setting the corresponding bit to 1 

resets the corresponding bit of DMAENi to 0.  

 

Figure 24-14 

DMAENi reset register (DMCLRi) (i=0~4). 

 

 

address: 40005020H (DMCLR0) , 40005021H (DMCLR1) ,  

40005022H (DMCLR2) , 40005023H (DMCLR3) ,  
40005024H (DMCLR4)  

after reset: 00H 

R/W 

 

symbol

 

7 

6 

5 

4 

3 

2 

1 

0 

DMCLRi 

DMCLRi7 

DMCLRi6 

DMCLRi5 

DMCLRi4 

DMCLRi3 

DMCLRi2 

DMCLRi1 

DMCLRi0 

 

 

DMSETin

 

Reset register for DMAENin

 

0

 

No reset is generated.

 

1

 

Reset the bit n of DMCENi to 0

 

 

Note: i=0

～

4

，

n=0~7

 

 
 

 

Summary of Contents for BAT32G1 9 Series






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for BAT32G1 9 Series

Samson 430 Series Mounting And Operating Instructions preview
430 Series
Brand: Samson Pages: 78
Rachio 3 Get Started preview
3
Brand: Rachio Pages: 16
Tech 21 MIDI MONGOOSE Owner'S Manual preview
MIDI MONGOOSE
Brand: Tech 21 Pages: 2
Ros IC-15X Operation And Maintenance Manual preview
IC-15X
Brand: Ros Pages: 10
Ezodo 4801P Manual preview
4801P
Brand: Ezodo Pages: 7
Hoffer 214D-1 User Manual preview
214D-1
Brand: Hoffer Pages: 57
Avenview SW-HBT4K-C6-4X4E Quick Start Manual preview
SW-HBT4K-C6-4X4E
Brand: Avenview Pages: 8
MAASLAND FLEXESS DUO Manual preview
FLEXESS DUO
Brand: MAASLAND Pages: 10
PPI Zenex Plus User Manual preview
Zenex Plus
Brand: PPI Pages: 27
Neousys Technology Nuvo-3000 Series User Manual preview
Nuvo-3000 Series
Brand: Neousys Technology Pages: 101
Maintronic CBA UP Manual preview
CBA UP
Brand: Maintronic Pages: 53
Delta ASD-B2-0121-B User Manual preview
ASD-B2-0121-B
Brand: Delta Pages: 313
Gardner Denver GD Connect 12 Manual preview
GD Connect 12
Brand: Gardner Denver Pages: 60
MEI 104/DSP Installation Manual preview
104/DSP
Brand: MEI Pages: 199
Zamel exta life ROB-21 Instructions Manual preview
exta life ROB-21
Brand: Zamel Pages: 24
BFT SECURBASE LIGHT PLUS Installation And User Manual preview
SECURBASE LIGHT PLUS
Brand: BFT Pages: 76
AUMA SQ 05.2-F05 Manual preview
SQ 05.2-F05
Brand: AUMA Pages: 72
LAE AC1-27 Series Instructions For Use preview
AC1-27 Series
Brand: LAE Pages: 2

Brands by name

Popular brands

Load more brands