manualshive.com logo in svg

CMOSTEK CMT216 Series, Operating Manual

Share
Download
CMOSTEK CMT216 Series Operating Manual Download Page 24

 
 

AN279 

 

 

Rev 0.7 | 24/32 

www.hoperf.com 

5 

 

Firmware Upgrade and Degrade Function 

WriterConfig can upgrade and degrade offline burner firmware versions. The update function synchronizes the 

offline burner firmware version with the latest release of WriterConfig. The degrade feature allows users to 

choose the burn firmware back to a lower suitable version. 

Before performing the upgrade and degration, make sure the offline burner connected to the computer 

through a USB cable, and the main interface of the WriterConfig program has been opened.

 

5.1   Firmware Upgrade 

When WriterConfig starts, it detects the firmware version of the burner. If the current firmware version is lower 

than WriterConfig version, it will automatically prompt the user whether to upgrade. Click OK to download and 

upgrade the firmware. Clicking Cancel will call off the upgrade. The details are shown in the following figure.

 

 

Figure 16. WriterConfig upgrade offline burner firmware 

 

 

Summary of Contents for CMT216 Series

































Reviews:

No comments

Brands by name

Popular brands

Load more brands