background image

WARNING

DANGER

WARNING

CAUTION

NOTICE

SAFETY 

GUIDE

Carbon dioxide is known as an asphyxiant gas.  Carbon dioxide poisoning has been linked 
to various health issues, including central nervous system damage, permanent deterioration 
of respiratory functions, suffocation or even death.  If you have any health concerns that may 
be related to the Product’s use of carbon dioxide, consult your doctor before using any of the 
Products. 

• CO₂ Levels can be measured using a CO₂ Monitor.
• 5,000 PPM is the workplace exposure limit in most jurisdictions.
• Check with your local agency to verify any need for permits in your area.

To ensure safe operation, user must follow instructions closely. Necessary protocols should be followed when 
handling and operating Special Effects Equipment and their respective consumables.

• Never place objects of any kind inside barrels.
• Never aim or fire the products at any person or living thing. 
• This product is meant to be used only in well-ventilated areas.

When using the products, always follow the safety radius displayed in this manual.

Once the product is attached to the CO₂ tanks and the tanks are turned on, the product, hoses and fittings will 
be under high pressure.  Do not disconnect any fittings or hoses until the tank has been turned off, and the 
remaining gas has been cleared through the product, depleting all pressure in the system. If a leak is detected, 
cease use of the product immediately. Never stand directly over unit while under pressure. Jets should be 
mounted or fixed in a safe place.  When using Jets above ground, always use a safety cable in the event the 
Product’s mount or fixture should fail.  You must supply the safety cable(s) to use with this product.  If you are 
under 18, you should not be using this product.

Preventing Serious Injury or Death

CO2 Special Effects are to only to be used in well ventilated areas. Failure to do so may result in oxygen 
displacement.

Maintain a safe distance between Special Effects Products and audience, crew & event staff. Refer to the safety 
radius outlined in this manual.

Never aim Special Effects Products directly at any person or living thing.

Always fasten tanks to avoid tipping, rocking, or being tampered with. When feasible, keep tanks out of direct 
sunlight.

Check with officials in local jurisdiction for any permit requirements before operating Special Effects.

This icon signifies that severe 

bodily harm or death 

will

 

occur if instuctions are not 

followed.

This icon signifies that severe 

bodily harm or death 

may

 

occur if instuctions are not 

followed.

This icon signifies that mild 

to moderate injury may 

occur if instuctions are not 

followed.

This icon signifies product 

malfunction or damage may 

occur if instructions are not 

followed.

3

Summary of Contents for QUAD JET





















Reviews: