ClimaCheck NX400 Hardware Manual Download

Page: 21 / 41

ClimaCheck Gateway NX400 Hardware Manual

–

2020-03-26 Page 21 of 41

Figure 10 USB memory with data from two different Gateways

To deactivate logging to USB:

•

Press ESC to enter the Main menu

•

Press down until “USB/Backup” appears in the display

•

Press SEL to enter USB/Backup menu

•

“Logg data to USB”

appears in the display

•

Press SEL to enter the menu,

•

Press No and then confirm with OK

3.15

Backup configuration to USB memory

The present configuration in the unit can be backed up to a USB memory connected to the USB-
port on the top side of the unit, see Figure 31.

To save the configuration:

•

Shut off logger by disconnecting power

•

Connect the USB memory to the USB-A port on top side of the unit.

•

Start logger by connecting power again. Wait for the unit to start.

•

Press ESC to enter the Main menu

•

Press down until “

USB/Backup

”

appears in the display

•

Press SEL to enter USB/Backup menu

•

Press down until “

Backup/Restore config

”

appears in the display

•

Press SEL to enter menu

•

Press

“Backup to USB” and confirm with OK

A *.cfg file is created on the USB memory with the PA-id as name.

3.16

Backup configuration to Internal memory

The present configuration in the unit can be backed up the internal memory of the unit

To save the configuration:

•

Press ESC to enter the Main menu

•

Press down until “

USB/Backup

”

appears in the display

•

Press SEL to enter USB/Backup menu

•

Press down until “

Backup/Restore config

”

appears in the display

•

Press SEL to enter menu

•

Press “Backup intern” and confirm with OK

Summary of Contents for NX400










































Search results

Summary of Contents for NX400

Reviews:

Related manuals for NX400

Brands by name

Popular brands

ClimaCheck NX400, Hardware Manual

Search results

Summary of Contents for NX400

Reviews:

Related manuals for NX400

Brands by name

Popular brands