manualshive.com logo in svg

Clevo P6x0Hx, User Manual

Share
Download
Clevo P6x0Hx User Manual Download Page 160

Modules

6 - 2 Setting Up SATA RAID, Optane™ or AHCI Mode

6

Setting Up SATA RAID, Optane™ or AHCI Mode

Note that your system can be set up as a RAID OR to support Intel® Optane™,
it cannot be set to support both systems.

AHCI Mode

Advanced Host Controller Interface (AHCI) is an interface specification that allows
the storage driver to enable advanced serial ATA features such as Native Command
Queuing (for maximum hard disk efficiency and performance). AHCI mode can be
supported by one or two hard disks/solid state drives. Make sure you install the 

In-

tel® Rapid Storage Technology 

application if you have set up your HDDs/SSDs

in 

AHCI

 mode (see 

“Intel® Rapid Storage Technology” on page 6 - 56

)

Intel® Optane™

Intel® Optane™ 

is a combination of a compatible memory device and 

Intel Rapid

Technology software

. This combination is designed to speed up your system per-

formance by caching boot data, executables, frequently accessed data and system
page files to an non volatile, low latency Intel® Optane™ SSD.

Contact your distributor or supplier to see if your system supports this technology.

RAID

To configure your RAID (Redundant Array of Independent Disks) system in Strip-
ing (RAID 0) or Mirroring (RAID 1) modes (see 

Table 6 - 1, on page 6 - 4

) you will

require 

at least

 

two

 

identical

 (see sidebar) HDDs/SSDs.

RAID Hard Disks/

Solid State Drives

All HDDS/SSDs in a
RAID should be identi-
cal (the same size and
brand) in order to pre-
vent unexpected system
behavior.

SATA Mode 

Selection

The SATA mode selec-
tion should be made 

be-

fore installing your
operating system

. 

DO NOT change your
selected SATA mode

unless you intend to re-
install your operating
system. Make sure you
have backed up all your
data before doing so.

Summary of Contents for P6x0Hx

















































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands