English
English
16
17
Item Number: 2608
OPERATION
Before the first use
• Carefully remove the steam broom and accessories from the packaging and check the appliance
for completeness and damage. Do not use damaged components.
In such a case, contact the customer service department.
• Remove all transport packaging and protective films from the steam broom and accessories
There may be water residue in the water tank. This is not a defect.
This only shows that the device has been tested by the quality assurance department.
Assembly
1. Insert the main unit [A] into the holding device [B] until it clicks into place.
You can remove the main unit [A] by pressing the locking button [6].
2. Push the holding device [B] onto the steam foot [M] until it clicks into place.
By pressing the re- lease button on the back, you can remove the steam foot [M]
from the holding device [B].
3. Fold the handle [2] upwards until it clicks into place. Fold the handle [2] back together
with the locking button on the articulated joint [1].
4. Pull the antiviral mop [K] over the steam foot [M] and tighten it with the cord.
5. To clean carpets, place the carpet slider [N] on the steam foot [M]
We recommend that the surfaces to be cleaned should be thoroughly
vacuumed or cleaned of crumbs and the like before using the steam broom.
Filling the water tank
Method 1 - Fill the inserted water tank
1. Turn the water tank cover [13] counterclockwise to open the water tank [15].
2. Fill the water tank [15] with the supplied measuring cup [J].
3. Insert the cover [13] and turn it clockwise to tighten it.
Method 2 - Fill the removed water tank
1. Pull the water tank [15] out of the main unit [A] by pressing and holding
both lock buttons on the water tank [14].
2. Turn the water tank cover [15] counterclockwise to open the water tank [15].
3. Hold the water tank [15] under a tap and fill it.
4. Insert the cover [13], and then turn it clockwise to tighten it.
5. Reinsert the water tank into the main unit [A] until it clicks into place.
Steam cleaning of surfaces
1. Insert the mains plug into a socket.
2. Turn on the machine with the Power Key [9].
3. The lamps [10] start to light up red to indicate that the steam broom is in the heating phase.
Heating up takes about 25 seconds. As soon as the lamps [10] light up blue, the machine is ready for operation.
A full water tank is sufficient for about 20 minutes.
If the power supply is interrupted during or after preheating,
the appliance will repeat the heating process described above.
4. You can regulate the steam quantity with the steam controller [12].
Turn the knob counterclo- ckwise to decrease the steam quantity and turn it
clockwise to increase the steam quantity.
De
utsc
h
NOTE:
Each steam mop is 100% tested in the factory to ensure product performance and
safety.When assembling your new steam mop for the first time you may notice water residue
inside of the unit.
!WARNING:
Before attempting any of the following operations,make sure that the appliance is
switched off and unplugged and that the appliance is cold and contains minimal or no water.
Spread holder
Round the holder along spindle until click to fix holder.
Press spindle button 1,turn the holder,the holder can become folded state.
Attaching the steam head
Slide the bottom end of main body onto
the steam head M until Steam head Spindle 5
clicks into place
The steam head M can be removed from the
Main body by pressing salient point on the
Steam head Spindle 5
Attaching a cleaning pad
Because of barb design at the bottom of steam head M,just
place a micro-fiber cleaning pad L to steam had,they can
bond hard.
Place the front of your shoe onto the cleaning pad removal
Tab and press down firmly.
Attaching Carpet Gilder
Press the micro-fiber cleaning pad L with main body to
Carpet gilder O by vertical pressure
，
until it into place.
Place the front of your shoe onto the cleaning pad removal
Tab and press down firmly,carpet gilder will remove form
steam head
Page 5 of 10
NOTE:
Each steam mop is 100% tested in the factory to ensure product performance and
safety.When assembling your new steam mop for the first time you may notice water residue
inside of the unit.
!WARNING:
Before attempting any of the following operations,make sure that the appliance is
switched off and unplugged and that the appliance is cold and contains minimal or no water.
Spread holder
Round the holder along spindle until click to fix holder.
Press spindle button 1,turn the holder,the holder can become folded state.
Attaching the steam head
Slide the bottom end of main body onto
the steam head M until Steam head Spindle 5
clicks into place
The steam head M can be removed from the
Main body by pressing salient point on the
Steam head Spindle 5
Attaching a cleaning pad
Because of barb design at the bottom of steam head M,just
place a micro-fiber cleaning pad L to steam had,they can
bond hard.
Place the front of your shoe onto the cleaning pad removal
Tab and press down firmly.
Attaching Carpet Gilder
Press the micro-fiber cleaning pad L with main body to
Carpet gilder O by vertical pressure
，
until it into place.
Place the front of your shoe onto the cleaning pad removal
Tab and press down firmly,carpet gilder will remove form
steam head
Page 5 of 10
ASSEMBLY
NOTE:
Each steam mop is 100% tested in the factory to ensure product performance and
safety.When assembling your new steam mop for the first time you may notice water residue
inside of the unit.
!WARNING:
Before attempting any of the following operations,make sure that the appliance is
switched off and unplugged and that the appliance is cold and contains minimal or no water.
Spread holder
Round the holder along spindle until click to fix holder.
Press spindle button 1,turn the holder,the holder can become folded state.
Attaching the steam head
Slide the bottom end of main body onto
the steam head M until Steam head Spindle 5
clicks into place
The steam head M can be removed from the
Main body by pressing salient point on the
Steam head Spindle 5
Attaching a cleaning pad
Because of barb design at the bottom of steam head M,just
place a micro-fiber cleaning pad L to steam had,they can
bond hard.
Place the front of your shoe onto the cleaning pad removal
Tab and press down firmly.
Attaching Carpet Gilder
Press the micro-fiber cleaning pad L with main body to
Carpet gilder O by vertical pressure
，
until it into place.
Place the front of your shoe onto the cleaning pad removal
Tab and press down firmly,carpet gilder will remove form
steam head
Page 5 of 10
ASSEMBLY
NOTE:
Each steam mop is 100% tested in the factory to ensure product performance and
safety.When assembling your new steam mop for the first time you may notice water residue
inside of the unit.
!WARNING:
Before attempting any of the following operations,make sure that the appliance is
switched off and unplugged and that the appliance is cold and contains minimal or no water.
Spread holder
Round the holder along spindle until click to fix holder.
Press spindle button 1,turn the holder,the holder can become folded state.
Attaching the steam head
Slide the bottom end of main body onto
the steam head M until Steam head Spindle 5
clicks into place
The steam head M can be removed from the
Main body by pressing salient point on the
Steam head Spindle 5
Attaching a cleaning pad
Because of barb design at the bottom of steam head M,just
place a micro-fiber cleaning pad L to steam had,they can
bond hard.
Place the front of your shoe onto the cleaning pad removal
Tab and press down firmly.
Attaching Carpet Gilder
Press the micro-fiber cleaning pad L with main body to
Carpet gilder O by vertical pressure
，
until it into place.
Place the front of your shoe onto the cleaning pad removal
Tab and press down firmly,carpet gilder will remove form
steam head
Page 5 of 10
Method one:
：
Open the water tank cup 5 by counterclockwise
rotation,fill 360ML water use Measuring cup,
and then clockwise rotation to close water tank cup 5.
Method two
：
Remove the water tank from main body,open the
water tank cup 5 by counterclockwise rotation,fill
the water tank from water faucet.,and then clockwise
rotation to close water tank cup 5.
Install the water tank 7to main body until it clicks into place.
2.Plug in the appliance to a grounded outlet.
3.When switch the appliance on,the indicator lights will turn red at the each side of water tank,it
indicate preheating.If the lights does not illuminate,please check the "troubleshooting" section for
more details.
4.It will takes approximately 25 seconds for preheating.Once the steam mop is ready to use the
water tank will glow blue.
5.When the water tank full fill with water,it can work approximately 20 minutes.If the water tank
7 without water,the indicator lights 12 will glow red,and the lights will flash to point out need to
add water
NOTICE
：
If power off during preheating or after preheating,then power again,the
appliance will repeat above preheating action.
6.Press the steam button 4 and steam button13,the steam out.
7.Add control volume by turn steam control knob 8
lockwise
，
and counterclockwise to reduce
，
User
can adjust steam volume according different objects
NOTICE
：
steam volume control by PCB,It will takes 3 seconds adaptation time
when you adjust steam volume .It is normal phenomenon.
8. When normal cleaning,the steam head
has big rotary angle,can clean corners
nd also can clean low space.
USE AS A STEAM CLEANER IN HAND
Push Lock Catch,take the main body A out of holder A,and also take out the power cord.
Install the accessory adaptor at the top of main body A,until it into place.
Press salient point at the accessory adaptor to remove the accessory adaptor from main body
A
Choose the appropriate accessories(check accessories use list),according to arrow indicator to
align and implant to accessory adaptor G,then turn anticlockwise,until it into place.
Page 6 of 10
rotation,fill 360ML water use Measuring cup,
and then clockwise rotation to close water tank cup 5.
Method two
：
Remove the water tank from main body,open the
water tank cup 5 by counterclockwise rotation,fill
the water tank from water faucet.,and then clockwise
rotation to close water tank cup 5.
Install the water tank 7to main body until it clicks into place.
2.Plug in the appliance to a grounded outlet.
3.When switch the appliance on,the indicator lights will turn red at the each side of water tank,it
indicate preheating.If the lights does not illuminate,please check the "troubleshooting" section for
more details.
4.It will takes approximately 25 seconds for preheating.Once the steam mop is ready to use the
water tank will glow blue.
5.When the water tank full fill with water,it can work approximately 20 minutes.If the water tank
7 without water,the indicator lights 12 will glow red,and the lights will flash to point out need to
add water
NOTICE
：
If power off during preheating or after preheating,then power again,the
appliance will repeat above preheating action.
6.Press the steam button 4 and steam button13,the steam out.
7.Add control volume by turn steam control knob 8
clockwise
，
and counterclockwise to reduce
，
User
can adjust steam volume according different objects
NOTICE
：
steam volume control by PCB,It will takes 3 seconds adaptation time
when you adjust steam volume .It is normal phenomenon.
8. When normal cleaning,the steam head
has big rotary angle,can clean corners
and also can clean low space.
USE AS A STEAM CLEANER IN HAND
Push Lock Catch,take the main body A out of holder A,and also take out the power cord.
Install the accessory adaptor at the top of main body A,until it into place.
Press salient point at the accessory adaptor to remove the accessory adaptor from main body
A
Choose the appropriate accessories(check accessories use list),according to arrow indicator to
align and implant to accessory adaptor G,then turn anticlockwise,until it into place.
Page 6 of 10
OPERATION
1.Filling the water tank
Method one:
：
Open the water tank cup 5 by counterclockwise
rotation,fill 360ML water use Measuring cup,
and then clockwise rotation to close water tank cup 5.
Method two
：
Remove the water tank from main body,open the
water tank cup 5 by counterclockwise rotation,fill
the water tank from water faucet.,and then clockwise
rotation to close water tank cup 5.
Install the water tank 7to main body until it clicks into place.
2.Plug in the appliance to a grounded outlet.
3.When switch the appliance on,the indicator lights will turn red at the each side of water tank,it
indicate preheating.If the lights does not illuminate,please check the "troubleshooting" section for
more details.
4.It will takes approximately 25 seconds for preheating.Once the steam mop is ready to use the
water tank will glow blue.
5.When the water tank full fill with water,it can work approximately 20 minutes.If the water tank
7 without water,the indicator lights 12 will glow red,and the lights will flash to point out need to
add water
NOTICE
：
If power off during preheating or after preheating,then power again,the
appliance will repeat above preheating action.
6.Press the steam button 4 and steam button13,the steam out.
7.Add control volume by turn steam control knob 8
clockwise
，
and counterclockwise to reduce
，
User
can adjust steam volume according different objects
NOTICE
：
steam volume control by PCB,It will takes 3 seconds adaptation time
when you adjust steam volume .It is normal phenomenon.
8. When normal cleaning,the steam head
has big rotary angle,can clean corners
and also can clean low space.
USE AS A STEAM CLEANER IN HAND
Push Lock Catch,take the main body A out of holder A,and also take out the power cord.
Install the accessory adaptor at the top of main body A,until it into place.
Press salient point at the accessory adaptor to remove the accessory adaptor from main body
A
Choose the appropriate accessories(check accessories use list),according to arrow indicator to
align and implant to accessory adaptor G,then turn anticlockwise,until it into place.
Page 6 of 10
De
utsc
h
NOTE:
Each steam mop is 100% tested in the factory to ensure product performance and
safety.When assembling your new steam mop for the first time you may notice water residue
inside of the unit.
!WARNING:
Before attempting any of the following operations,make sure that the appliance is
switched off and unplugged and that the appliance is cold and contains minimal or no water.
Spread holder
Round the holder along spindle until click to fix holder.
Press spindle button 1,turn the holder,the holder can become folded state.
Attaching the steam head
Slide the bottom end of main body onto
the steam head M until Steam head Spindle 5
clicks into place
The steam head M can be removed from the
Main body by pressing salient point on the
Steam head Spindle 5
Attaching a cleaning pad
Because of barb design at the bottom of steam head M,just
place a micro-fiber cleaning pad L to steam had,they can
bond hard.
Place the front of your shoe onto the cleaning pad removal
Tab and press down firmly.
Attaching Carpet Gilder
Press the micro-fiber cleaning pad L with main body to
Carpet gilder O by vertical pressure
，
until it into place.
Place the front of your shoe onto the cleaning pad removal
Tab and press down firmly,carpet gilder will remove form
steam head
Page 5 of 10
NOTE:
Each steam mop is 100% tested in the factory to ensure product performance and
safety.When assembling your new steam mop for the first time you may notice water residue
inside of the unit.
!WARNING:
Before attempting any of the following operations,make sure that the appliance is
switched off and unplugged and that the appliance is cold and contains minimal or no water.
Spread holder
Round the holder along spindle until click to fix holder.
Press spindle button 1,turn the holder,the holder can become folded state.
Attaching the steam head
Slide the bottom end of main body onto
the steam head M until Steam head Spindle 5
clicks into place
The steam head M can be removed from the
Main body by pressing salient point on the
Steam head Spindle 5
Attaching a cleaning pad
Because of barb design at the bottom of steam head M,just
place a micro-fiber cleaning pad L to steam had,they can
bond hard.
Place the front of your shoe onto the cleaning pad removal
Tab and press down firmly.
Attaching Carpet Gilder
Press the micro-fiber cleaning pad L with main body to
Carpet gilder O by vertical pressure
，
until it into place.
Place the front of your shoe onto the cleaning pad removal
Tab and press down firmly,carpet gilder will remove form
steam head
Page 5 of 10
ASSEMBLY
NOTE:
Each steam mop is 100% tested in the factory to ensure product performance and
safety.When assembling your new steam mop for the first time you may notice water residue
inside of the unit.
!WARNING:
Before attempting any of the following operations,make sure that the appliance is
switched off and unplugged and that the appliance is cold and contains minimal or no water.
Spread holder
Round the holder along spindle until click to fix holder.
Press spindle button 1,turn the holder,the holder can become folded state.
Attaching the steam head
Slide the bottom end of main body onto
the steam head M until Steam head Spindle 5
clicks into place
The steam head M can be removed from the
Main body by pressing salient point on the
Steam head Spindle 5
Attaching a cleaning pad
Because of barb design at the bottom of steam head M,just
place a micro-fiber cleaning pad L to steam had,they can
bond hard.
Place the front of your shoe onto the cleaning pad removal
Tab and press down firmly.
Attaching Carpet Gilder
Press the micro-fiber cleaning pad L with main body to
Carpet gilder O by vertical pressure
，
until it into place.
Place the front of your shoe onto the cleaning pad removal
Tab and press down firmly,carpet gilder will remove form
steam head
Page 5 of 10
ASSEMBLY
NOTE:
Each steam mop is 100% tested in the factory to ensure product performance and
safety.When assembling your new steam mop for the first time you may notice water residue
inside of the unit.
!WARNING:
Before attempting any of the following operations,make sure that the appliance is
switched off and unplugged and that the appliance is cold and contains minimal or no water.
Spread holder
Round the holder along spindle until click to fix holder.
Press spindle button 1,turn the holder,the holder can become folded state.
Attaching the steam head
Slide the bottom end of main body onto
the steam head M until Steam head Spindle 5
clicks into place
The steam head M can be removed from the
Main body by pressing salient point on the
Steam head Spindle 5
Attaching a cleaning pad
Because of barb design at the bottom of steam head M,just
place a micro-fiber cleaning pad L to steam had,they can
bond hard.
Place the front of your shoe onto the cleaning pad removal
Tab and press down firmly.
Attaching Carpet Gilder
Press the micro-fiber cleaning pad L with main body to
Carpet gilder O by vertical pressure
，
until it into place.
Place the front of your shoe onto the cleaning pad removal
Tab and press down firmly,carpet gilder will remove form
steam head
Page 5 of 10
Method one:
：
Open the water tank cup 5 by counterclockwise
rotation,fill 360ML water use Measuring cup,
and then clockwise rotation to close water tank cup 5.
Method two
：
Remove the water tank from main body,open the
water tank cup 5 by counterclockwise rotation,fill
the water tank from water faucet.,and then clockwise
rotation to close water tank cup 5.
Install the water tank 7to main body until it clicks into place.
2.Plug in the appliance to a grounded outlet.
3.When switch the appliance on,the indicator lights will turn red at the each side of water tank,it
indicate preheating.If the lights does not illuminate,please check the "troubleshooting" section for
more details.
4.It will takes approximately 25 seconds for preheating.Once the steam mop is ready to use the
water tank will glow blue.
5.When the water tank full fill with water,it can work approximately 20 minutes.If the water tank
7 without water,the indicator lights 12 will glow red,and the lights will flash to point out need to
add water
NOTICE
：
If power off during preheating or after preheating,then power again,the
appliance will repeat above preheating action.
6.Press the steam button 4 and steam button13,the steam out.
7.Add control volume by turn steam control knob 8
lockwise
，
and counterclockwise to reduce
，
User
can adjust steam volume according different objects
NOTICE
：
steam volume control by PCB,It will takes 3 seconds adaptation time
when you adjust steam volume .It is normal phenomenon.
8. When normal cleaning,the steam head
has big rotary angle,can clean corners
nd also can clean low space.
USE AS A STEAM CLEANER IN HAND
Push Lock Catch,take the main body A out of holder A,and also take out the power cord.
Install the accessory adaptor at the top of main body A,until it into place.
Press salient point at the accessory adaptor to remove the accessory adaptor from main body
A
Choose the appropriate accessories(check accessories use list),according to arrow indicator to
align and implant to accessory adaptor G,then turn anticlockwise,until it into place.
Page 6 of 10
rotation,fill 360ML water use Measuring cup,
and then clockwise rotation to close water tank cup 5.
Method two
：
Remove the water tank from main body,open the
water tank cup 5 by counterclockwise rotation,fill
the water tank from water faucet.,and then clockwise
rotation to close water tank cup 5.
Install the water tank 7to main body until it clicks into place.
2.Plug in the appliance to a grounded outlet.
3.When switch the appliance on,the indicator lights will turn red at the each side of water tank,it
indicate preheating.If the lights does not illuminate,please check the "troubleshooting" section for
more details.
4.It will takes approximately 25 seconds for preheating.Once the steam mop is ready to use the
water tank will glow blue.
5.When the water tank full fill with water,it can work approximately 20 minutes.If the water tank
7 without water,the indicator lights 12 will glow red,and the lights will flash to point out need to
add water
NOTICE
：
If power off during preheating or after preheating,then power again,the
appliance will repeat above preheating action.
6.Press the steam button 4 and steam button13,the steam out.
7.Add control volume by turn steam control knob 8
clockwise
，
and counterclockwise to reduce
，
User
can adjust steam volume according different objects
NOTICE
：
steam volume control by PCB,It will takes 3 seconds adaptation time
when you adjust steam volume .It is normal phenomenon.
8. When normal cleaning,the steam head
has big rotary angle,can clean corners
and also can clean low space.
USE AS A STEAM CLEANER IN HAND
Push Lock Catch,take the main body A out of holder A,and also take out the power cord.
Install the accessory adaptor at the top of main body A,until it into place.
Press salient point at the accessory adaptor to remove the accessory adaptor from main body
A
Choose the appropriate accessories(check accessories use list),according to arrow indicator to
align and implant to accessory adaptor G,then turn anticlockwise,until it into place.
Page 6 of 10
OPERATION
1.Filling the water tank
Method one:
：
Open the water tank cup 5 by counterclockwise
rotation,fill 360ML water use Measuring cup,
and then clockwise rotation to close water tank cup 5.
Method two
：
Remove the water tank from main body,open the
water tank cup 5 by counterclockwise rotation,fill
the water tank from water faucet.,and then clockwise
rotation to close water tank cup 5.
Install the water tank 7to main body until it clicks into place.
2.Plug in the appliance to a grounded outlet.
3.When switch the appliance on,the indicator lights will turn red at the each side of water tank,it
indicate preheating.If the lights does not illuminate,please check the "troubleshooting" section for
more details.
4.It will takes approximately 25 seconds for preheating.Once the steam mop is ready to use the
water tank will glow blue.
5.When the water tank full fill with water,it can work approximately 20 minutes.If the water tank
7 without water,the indicator lights 12 will glow red,and the lights will flash to point out need to
add water
NOTICE
：
If power off during preheating or after preheating,then power again,the
appliance will repeat above preheating action.
6.Press the steam button 4 and steam button13,the steam out.
7.Add control volume by turn steam control knob 8
clockwise
，
and counterclockwise to reduce
，
User
can adjust steam volume according different objects
NOTICE
：
steam volume control by PCB,It will takes 3 seconds adaptation time
when you adjust steam volume .It is normal phenomenon.
8. When normal cleaning,the steam head
has big rotary angle,can clean corners
and also can clean low space.
USE AS A STEAM CLEANER IN HAND
Push Lock Catch,take the main body A out of holder A,and also take out the power cord.
Install the accessory adaptor at the top of main body A,until it into place.
Press salient point at the accessory adaptor to remove the accessory adaptor from main body
A
Choose the appropriate accessories(check accessories use list),according to arrow indicator to
align and implant to accessory adaptor G,then turn anticlockwise,until it into place.
Page 6 of 10
Method one:
：
Open the water tank cup 5 by counterclockwise
rotation,fill 360ML water use Measuring cup,
and then clockwise rotation to close water tank cup 5.
Method two
：
Remove the water tank from main body,open the
water tank cup 5 by counterclockwise rotation,fill
the water tank from water faucet.,and then clockwise
rotation to close water tank cup 5.
Install the water tank 7to main body until it clicks into place.
2.Plug in the appliance to a grounded outlet.
3.When switch the appliance on,the indicator lights will turn red at the each side of water tank,it
indicate preheating.If the lights does not illuminate,please check the "troubleshooting" section for
more details.
4.It will takes approximately 25 seconds for preheating.Once the steam mop is ready to use the
water tank will glow blue.
5.When the water tank full fill with water,it can work approximately 20 minutes.If the water tank
7 without water,the indicator lights 12 will glow red,and the lights will flash to point out need to
add water
NOTICE
：
If power off during preheating or after preheating,then power again,the
appliance will repeat above preheating action.
6.Press the steam button 4 and steam button13,the steam out.
7.Add control volume by turn steam control knob 8
lockwise
，
and counterclockwise to reduce
，
User
can adjust steam volume according different objects
NOTICE
：
steam volume control by PCB,It will takes 3 seconds adaptation time
when you adjust steam volume .It is normal phenomenon.
8. When normal cleaning,the steam head
has big rotary angle,can clean corners
nd also can clean low space.
USE AS A STEAM CLEANER IN HAND
Push Lock Catch,take the main body A out of holder A,and also take out the power cord.
Install the accessory adaptor at the top of main body A,until it into place.
Press salient point at the accessory adaptor to remove the accessory adaptor from main body
A
Choose the appropriate accessories(check accessories use list),according to arrow indicator to
align and implant to accessory adaptor G,then turn anticlockwise,until it into place.
Page 6 of 10
rotation,fill 360ML water use Measuring cup,
and then clockwise rotation to close water tank cup 5.
Method two
：
Remove the water tank from main body,open the
water tank cup 5 by counterclockwise rotation,fill
the water tank from water faucet.,and then clockwise
rotation to close water tank cup 5.
Install the water tank 7to main body until it clicks into place.
2.Plug in the appliance to a grounded outlet.
3.When switch the appliance on,the indicator lights will turn red at the each side of water tank,it
indicate preheating.If the lights does not illuminate,please check the "troubleshooting" section for
more details.
4.It will takes approximately 25 seconds for preheating.Once the steam mop is ready to use the
water tank will glow blue.
5.When the water tank full fill with water,it can work approximately 20 minutes.If the water tank
7 without water,the indicator lights 12 will glow red,and the lights will flash to point out need to
add water
NOTICE
：
If power off during preheating or after preheating,then power again,the
appliance will repeat above preheating action.
6.Press the steam button 4 and steam button13,the steam out.
7.Add control volume by turn steam control knob 8
clockwise
，
and counterclockwise to reduce
，
User
can adjust steam volume according different objects
NOTICE
：
steam volume control by PCB,It will takes 3 seconds adaptation time
when you adjust steam volume .It is normal phenomenon.
8. When normal cleaning,the steam head
has big rotary angle,can clean corners
and also can clean low space.
USE AS A STEAM CLEANER IN HAND
Push Lock Catch,take the main body A out of holder A,and also take out the power cord.
Install the accessory adaptor at the top of main body A,until it into place.
Press salient point at the accessory adaptor to remove the accessory adaptor from main body
A
Choose the appropriate accessories(check accessories use list),according to arrow indicator to
align and implant to accessory adaptor G,then turn anticlockwise,until it into place.
Page 6 of 10
OPERATION
1.Filling the water tank
Method one:
：
Open the water tank cup 5 by counterclockwise
rotation,fill 360ML water use Measuring cup,
and then clockwise rotation to close water tank cup 5.
Method two
：
Remove the water tank from main body,open the
water tank cup 5 by counterclockwise rotation,fill
the water tank from water faucet.,and then clockwise
rotation to close water tank cup 5.
Install the water tank 7to main body until it clicks into place.
2.Plug in the appliance to a grounded outlet.
3.When switch the appliance on,the indicator lights will turn red at the each side of water tank,it
indicate preheating.If the lights does not illuminate,please check the "troubleshooting" section for
more details.
4.It will takes approximately 25 seconds for preheating.Once the steam mop is ready to use the
water tank will glow blue.
5.When the water tank full fill with water,it can work approximately 20 minutes.If the water tank
7 without water,the indicator lights 12 will glow red,and the lights will flash to point out need to
add water
NOTICE
：
If power off during preheating or after preheating,then power again,the
appliance will repeat above preheating action.
6.Press the steam button 4 and steam button13,the steam out.
7.Add control volume by turn steam control knob 8
clockwise
，
and counterclockwise to reduce
，
User
can adjust steam volume according different objects
NOTICE
：
steam volume control by PCB,It will takes 3 seconds adaptation time
when you adjust steam volume .It is normal phenomenon.
8. When normal cleaning,the steam head
has big rotary angle,can clean corners
and also can clean low space.
USE AS A STEAM CLEANER IN HAND
Push Lock Catch,take the main body A out of holder A,and also take out the power cord.
Install the accessory adaptor at the top of main body A,until it into place.
Press salient point at the accessory adaptor to remove the accessory adaptor from main body
A
Choose the appropriate accessories(check accessories use list),according to arrow indicator to
align and implant to accessory adaptor G,then turn anticlockwise,until it into place.
Page 6 of 10
5. Place the steam foot on the floor and tilt the steam broom back slightly.
6. Press and hold the steam knob [4] on the handle to release steam. This takes a few seconds.
For full cleaning power, steam the dry antiviral mop [K] for about 30 seconds. During cleaning, press the steam button [4]
intermittently to avoid over-wetting the antiviral mop.
7. Clean the floor.
8. Press the On / Off key [9] again to switch the steam brush off.
The adjustment time for steam setting is about three seconds.
The steam foot should not be on the same spot for a long-time during cleaning and should always be in motion.
In this wayyou avoid over-wetting.
If water or steam should unexpectedly escape from unintended places during the cleaning process, stop operation immedi-
ately and remove the mains plug. Contact the customer ser- vice!
Method one:
：
Open the water tank cup 5 by counterclockwise
rotation,fill 360ML water use Measuring cup,
and then clockwise rotation to close water tank cup 5.
Method two
：
Remove the water tank from main body,open the
water tank cup 5 by counterclockwise rotation,fill
the water tank from water faucet.,and then clockwise
rotation to close water tank cup 5.
Install the water tank 7to main body until it clicks into place.
2.Plug in the appliance to a grounded outlet.
3.When switch the appliance on,the indicator lights will turn red at the each side of water tank,it
indicate preheating.If the lights does not illuminate,please check the "troubleshooting" section for
more details.
4.It will takes approximately 25 seconds for preheating.Once the steam mop is ready to use the
water tank will glow blue.
5.When the water tank full fill with water,it can work approximately 20 minutes.If the water tank
7 without water,the indicator lights 12 will glow red,and the lights will flash to point out need to
add water
NOTICE
：
If power off during preheating or after preheating,then power again,the
appliance will repeat above preheating action.
6.Press the steam button 4 and steam button13,the steam out.
7.Add control volume by turn steam control knob 8
lockwise
，
and counterclockwise to reduce
，
User
can adjust steam volume according different objects
NOTICE
：
steam volume control by PCB,It will takes 3 seconds adaptation time
when you adjust steam volume .It is normal phenomenon.
8. When normal cleaning,the steam head
has big rotary angle,can clean corners
nd also can clean low space.
USE AS A STEAM CLEANER IN HAND
Push Lock Catch,take the main body A out of holder A,and also take out the power cord.
Install the accessory adaptor at the top of main body A,until it into place.
Press salient point at the accessory adaptor to remove the accessory adaptor from main body
A
Choose the appropriate accessories(check accessories use list),according to arrow indicator to
align and implant to accessory adaptor G,then turn anticlockwise,until it into place.
Page 6 of 10
rotation,fill 360ML water use Measuring cup,
and then clockwise rotation to close water tank cup 5.
Method two
：
Remove the water tank from main body,open the
water tank cup 5 by counterclockwise rotation,fill
the water tank from water faucet.,and then clockwise
rotation to close water tank cup 5.
Install the water tank 7to main body until it clicks into place.
2.Plug in the appliance to a grounded outlet.
3.When switch the appliance on,the indicator lights will turn red at the each side of water tank,it
indicate preheating.If the lights does not illuminate,please check the "troubleshooting" section for
more details.
4.It will takes approximately 25 seconds for preheating.Once the steam mop is ready to use the
water tank will glow blue.
5.When the water tank full fill with water,it can work approximately 20 minutes.If the water tank
7 without water,the indicator lights 12 will glow red,and the lights will flash to point out need to
add water
NOTICE
：
If power off during preheating or after preheating,then power again,the
appliance will repeat above preheating action.
6.Press the steam button 4 and steam button13,the steam out.
7.Add control volume by turn steam control knob 8
clockwise
，
and counterclockwise to reduce
，
User
can adjust steam volume according different objects
NOTICE
：
steam volume control by PCB,It will takes 3 seconds adaptation time
when you adjust steam volume .It is normal phenomenon.
8. When normal cleaning,the steam head
has big rotary angle,can clean corners
and also can clean low space.
USE AS A STEAM CLEANER IN HAND
Push Lock Catch,take the main body A out of holder A,and also take out the power cord.
Install the accessory adaptor at the top of main body A,until it into place.
Press salient point at the accessory adaptor to remove the accessory adaptor from main body
A
Choose the appropriate accessories(check accessories use list),according to arrow indicator to
align and implant to accessory adaptor G,then turn anticlockwise,until it into place.
Page 6 of 10
OPERATION
1.Filling the water tank
Method one:
：
Open the water tank cup 5 by counterclockwise
rotation,fill 360ML water use Measuring cup,
and then clockwise rotation to close water tank cup 5.
Method two
：
Remove the water tank from main body,open the
water tank cup 5 by counterclockwise rotation,fill
the water tank from water faucet.,and then clockwise
rotation to close water tank cup 5.
Install the water tank 7to main body until it clicks into place.
2.Plug in the appliance to a grounded outlet.
3.When switch the appliance on,the indicator lights will turn red at the each side of water tank,it
indicate preheating.If the lights does not illuminate,please check the "troubleshooting" section for
more details.
4.It will takes approximately 25 seconds for preheating.Once the steam mop is ready to use the
water tank will glow blue.
5.When the water tank full fill with water,it can work approximately 20 minutes.If the water tank
7 without water,the indicator lights 12 will glow red,and the lights will flash to point out need to
add water
NOTICE
：
If power off during preheating or after preheating,then power again,the
appliance will repeat above preheating action.
6.Press the steam button 4 and steam button13,the steam out.
7.Add control volume by turn steam control knob 8
clockwise
，
and counterclockwise to reduce
，
User
can adjust steam volume according different objects
NOTICE
：
steam volume control by PCB,It will takes 3 seconds adaptation time
when you adjust steam volume .It is normal phenomenon.
8. When normal cleaning,the steam head
has big rotary angle,can clean corners
and also can clean low space.
USE AS A STEAM CLEANER IN HAND
Push Lock Catch,take the main body A out of holder A,and also take out the power cord.
Install the accessory adaptor at the top of main body A,until it into place.
Press salient point at the accessory adaptor to remove the accessory adaptor from main body
A
Choose the appropriate accessories(check accessories use list),according to arrow indicator to
align and implant to accessory adaptor G,then turn anticlockwise,until it into place.
Page 6 of 10
Changing the accessories
The Clever Clean ViralOff® steam broom can also be used as a hand steam cleaner and is supplied with a wide range of acces-
sories. This allows you to clean even hard-to-reach areas and objects for which the steam foot is unsuitable.
1. Press the locking key [6] to release the main unit [A] from the holding device [B]. The steam broom can now be used as a
practical hand steam broom.
2. Push the accessory adapter [F] onto the machine until it clicks into place.
3. Attach the desired accessory to the adapter [F] and rotate it clockwise.
4. To remove the accessory after cleaning, loosely rotate the accessory counterclockwise and pull it off the adapter [F].
5. To remove the adapter [F], press the lock button of the adapter [F] on the rear of the machine.
6. The main unit [A] can now be reinstalled in the holding device [B].
Attention! The bottom of the main unit [A] becomes hot during use! There is a danger of burns. Let the main unit [A] cool
down before touching it.
