DELUXE SYSTEM
OWNER’S MANUAL
READ AND FOLLOW ALL INSTRUCTIONS! SAVE THESE INSTRUCTIONS!
WARNING! To reduce the risk of injury and product damage:
Feeders are designed to use only Chlorine (Trichloro-s-triazinetrione) or Bromine
(Bromochloro -5, 5 Dimethylhydantoin) tablets, slow dissolving type.
UNDER NO
CIRCUMSTANCES
MIX Trichlor OR Bromine with Calcium Hypochlorite, with other forms of
concentrated chlorine, or with other chemicals
FIRE AND/OR EXPLOSION MAY RESULT
.
NEVER
use oils or grease to lubricate 0-ring. Oil in contact with Trichlor OR Bromine may result
in
FIRE
. Caution should be used when removing feeder cap. Do not inhale fumes.
If shock treatments or Algaecides containing chemicals other than sanitizer tablets in feeder
must be used, then turn off feeder OR remove tablets until the shock or algae treatment is
complete and all granules have dissolved. Failure to do so may result
in granules mixing in feeder causing
FIRE AND/OR EXPLOSION
. The shock or algae treatment
dissolved in water is safe with tablets.
ALWAYS WEAR PROTECTION
for eyes, skin and clothing when working with chemicals. Do
not smoke and avoid sparks and open flames. Turn off pump and control valve before opening
chlorinator. Use of bulk chemicals may result in damage to pool.
Chemicals will dissolve very quickly and may cause bleaching to liner due to over-chlorinating,
possibly causing unsafe pool conditions.
Settings in excess of the recommended control setting levels for the chlorinator can result in
excess chlorine being discharged in your pool. This can result in bleaching or discoloration of
areas around the pool inlet or in some cases bleaching of the entire pool liner or paint (
CHECK
CHEMICAL RESIDUALS REGULARLY
).
MOTOR DOES NOT START:
Make sure motor is plugged in.
Circuit breaker in OFF position.
Thermal Overload in tripped position.
WIRING INSTALLATION INCORRECT:
Incorrect line voltage.
Defective wiring.
THERMAL OVERLOAD TRIPS:
Low Voltage.
Wiring installation incorrect.
Dual voltage pumps mis-wired.
Inadequate ventilation.
NO WATER FLOW:
Obstruction of suction or return line.
Clogged impeller.
Suction system air leaks.
Slice Valve Closed.
Clogged Hose Fitting.
Clogged Basket.
Dirty Sand.
EXCESSIVE PUMP NOISE:
Worn Bearings.
Suction Line Clogged.
Pump incorrectly mounted.
Hose Fitting partially closed.
Slice Valve partially closed.
Clogged Trap Basket.
INADEQUATE FILTERING:
Sand level too low.
Inadequately cleaned system.
Excessive dirt load.
Chemical imbalance.
Inadequate system pressure.
Waterway Plastics manufactures its products and equipment in accordance with very high
standards of workmanship. We use the best materials available and maintain the highest quality
procedures practical in the industry. In accordance, Waterway warrants its products as follows:
All plastics parts such as jets, valves, skimmers, manifolds, suctions, lights, and other plastic
components manufactured by Waterway will be replaced or repaired if the defects are
determined by Waterway to be the responsibility of Waterway Plastics for a period of three years
from the date of installation. The warranty does not cover filter cartridges, D.E. grids, o-rings,
pressure gauges, pump seals, light bulbs or any parts not manufactured by Waterway. Warranty
applies to OEMs and Distributors of Waterway Products.
The Supreme and Hi-Flo Pumps will receive limited warranty from any defect in material or
workmanship of one year from the date of manufacture. This includes the motor but not the
motor seal.
All thermoplastic molded filter bodies and rotational molded sand filter bodies have a warranty
of ten years, warranted on a pro-rata life basis. If a defect becomes apparent during the first
year, the body will be exchanged for a new body if the defects are determined by Waterway to
be the responsibility of Waterway Plastics. If a defect becomes apparent after the first year from
the date of manufacture which, in the opinion of Waterway, will require replacement, the body
will be exchanged for a new tank on an adjusted service pro-rata life basis.
Charges to the owner, on the pro-rata life basis, will be determined by the actual number of
months installed beginning with the date of installation.
Products that fail or become defective during the warranty period, except as a result of improper
installation, bad water chemistry, accidents or negligence on behalf of the owner, freezing,
earthquakes, fire floods, or other acts of nature, shall be repaired or replaces at Waterway’s
option without charge to the owner. This process will be completed within 90 days of receipt
of the defective product barring delays caused by the acquisition of component parts not
manufactured at our facility.
To obtain warranty replacements or repair, defective products should be returned
(transportation paid) to the place of purchase, or to Waterway. It should include a description of
the defect and the circumstances surrounding the incident or problem.
Waterway shall not be responsible for cartage, removal and/or reinstallation labor, or any
other such costs incurred in obtaining warranty replacements. Warranty applies to OEMs and
Distributors of Waterway Products.
This warranty gives you specific legal rights. You may also have other rights which very from
state to state.
CHLORINATOR & BROMINATOR USE WARNINGS
TROUBLESHOOTING
LIMITED WARRANTY
Model FS016 - 50 lbs
Model FS019 - 100 lbs
Model FS022 - 150 lbs
Model FS026 - 200 lbs
SAND FILL CHART:
HIGH RATE SAND FILTER
2200 East Sturgis Road, Oxnard, CA 93030 • Ph. (805) 981-0262 • Fax (805) 981-9403
www.waterwayplastics.com • [email protected]
810-0081.1208
© Copyright 2008 Waterway Plastics
