ClearView Hawk04-HD Page 104 User Manual Download

Page: 104 / 155

Figure 7-30

Please refer to the following sheet for detailed information.

Parameter

Function

Channel

Here is for you to select a monitor channel.

Channel Name

Here is to display current channel name. You can modify it.

Compression

H.264

Main Stream

It includes main stream, motion stream and alarm stream. You can

select different encode frame rates form different recorded events.

System supports active control frame function (ACF). It allows you to

record in different frame rates.

For example, you can use high frame rate to record important events,

record scheduled event in lower frame rate and it allows you to set

different frame rates for motion detection record and alarm record.

Extra Stream

Select extra stream if you enabled the extension stream to monitor.

Audio/Video

For the main stream, recorded file only contains video by default. You

need to draw a circle here to enable audio function.

For extra stream, you need to draw a circle to select the video first and

then select the audio if necessary.

Resolution

System supports various resolutions, you can select from the dropdo

list. For this model, main stream supports D1/HD1/2CIF/CIF/QCIF.

�

For the 4-chahnel mode, the main stream supports

D1/HD1/2CIF/CIF/QCIF and the extra stream supports CIF/QCIF

�

For the 8/16-channel, the main stream supports

D1/HD1/2CIF/CIF/QCIF and the extra stream supports QCIF.

Frame Rate

Frame rate: It ranges from 1f/s to 25f/s in PAL mode and 1f/s to 30f/s

NTSC mode.

�

For the 4-channel series product: All-channel support s

D1/HD1/2CIF/CIF/QCIF and the frame rate ranges from 1f/s to 25f/s
in PAL mode and 1f/s to 30f/s in NTSC mode.

�

For the 8-channel series product: The resolution of 1-

channel and the 2-channel support D1/HD1/2CIF/CIF/QCIF (fra m
rate: 25/30fps), the resolution of rest channels (3-channel to 8-

channel) support D1/HD1 (frame rate ≤12/13fps),

2CIF/CIF/QCIF(frame rate: 25/30fps).

�

For the 16-channel series product: All -channel suppo

CIF/QCIF and the frame rate ranges from 1f/s to 25f/s in PAL m
and 1f/s to 30f/s in NTSC mode. All-channel support D1/HD1/2C
and the frame rate ranges from 1f/s to 6f/s in PAL mode and 1f/s
7f/s in NTSC mode.

Summary of Contents for Hawk04-HD




























































































































































Search results

Summary of Contents for Hawk04-HD

Reviews:

Related manuals for Hawk04-HD

Brands by name

Popular brands

ClearView Hawk04-HD, User Manual

Search results

Summary of Contents for Hawk04-HD

Reviews:

Related manuals for Hawk04-HD

Brands by name

Popular brands