CLEARPATH TurtleBot 4 Lite User Manual Download Page 47

Page: 47 / 153

ros2 run robot_upstart

install

turtlebot4_bringup/launch/lite.launch.py

--job

turtlebot4

--rmw

rmw_cyclonedds_cpp

--rmw_config

/etc/cyclonedds_rpi.xml

To uninstall, use this command:

ros2 run robot_upstart uninstall turtlebot4

Once uninstalled, the launch file will no longer be launched on boot.

Bringup

The

turtlebot4_bringup

package contains the launch and configuration files to run the robots

software.

Launch files:

●

Joy Teleop

: Launches nodes to enable the bluetooth controller.

●

OAKD

: Launches the OAK-D nodes.

●

RPLIDAR

: Launches the RPLIDAR node.

●

Robot

: Launches the TurtleBot 4 nodes.

●

Lite

: Launches all necessary nodes for the TurtleBot 4 Lite.

●

Standard

: Launches all necessary nodes for the TurtleBot 4.

Config files:

●

TurtleBot 4 Controller

: Configurations for the TurtleBot 4 controller.

●

TurtleBot 4

: Configurations for the

turtlebot4_node

and

turtlebot4_base_node

Diagnostics

The

turtlebot4_diagnostics

packages contains the source code and launch files for the TurtleBot

4 diagnostics updater.

Launch files:

●

Diagnostics

: Launches the turtlebot4 diagnostics updater and the diagnostic aggregator

node.

Diagnostics Updater

The

diagnostics updater

is a Python3 node that runs on the robot. It subscribes to diagnostic

topics records statistics specific to each topic. The diagnostic data is viewable with

rqt_robot_monitor

Summary of Contents for TurtleBot 4 Lite


























































































































































Search results

Summary of Contents for TurtleBot 4 Lite

Reviews:

Related manuals for TurtleBot 4 Lite

Brands by name

Popular brands

CLEARPATH TurtleBot 4 Lite, User Manual

Search results

Summary of Contents for TurtleBot 4 Lite

Reviews:

Related manuals for TurtleBot 4 Lite

Brands by name

Popular brands