background image

W A R R A N T Y

i v                                

PROFITS). SOME STATES DO NOT ALLOW THE EXCLUSION OR 
LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES OR 
THE LIMITATION ON HOW LONG AN IMPLIED WARRANTY LASTS, 
SO THE ABOVE LIMITATIONS MAY NOT APPLY TO YOU. IN ANY 
EVENT, TO THE MAXIMUM EXTENT PERMITTED UNDER 
APPLICABLE LAW, CLEAR-COM'S LIABILITY TO CUSTOMER 
HEREUNDER SHALL NOT UNDER ANY CIRCUMSTANCES EXCEED 
THE COST OF REPAIRING OR REPLACING ANY PART(S) FOUND TO 
BE DEFECTIVE WITHIN THE WARRANTY PERIOD AS AFORESAID.

This warranty does not cover any damage to a product resulting from cause 
other than part defect and malfunction. The Clear-Com warranty does not 
cover any defect, malfunction, or failure caused beyond the control of 
Clear-Com, including unreasonable or negligent operation, abuse, accident, 
failure to follow instructions in the manual, defective or improperly 
associated equipment, attempts at modification and repair not approved by 
Clear-Com, and shipping damage. Products with their serial numbers 
removed or defaced are not covered by this warranty. 

This warranty does not include defects arising from installation (when not 
performed by Clear-Com), lightning, power outages and fluctuations, air 
conditioning failure, improper integration with non-approved components, 
defects or failures of customer furnished components resulting in damage to 
Clear-Com provided product. 

This limited warranty is not transferable and cannot be enforced by anyone 
other than the original consumer purchaser. 

This warranty gives you specific legal rights and you may have other rights 
which vary from country to country.

Summary of Contents for PS-702





























Reviews: