background image

 

 

SAFETY INFORMATION                                              

CHAPTER 2 

SAFETY WARNINGS

 

Two aspects of ClearWater Tech ozone generators represent potential dangers – ozone gas and high voltage electricity. 

 
OZONE GAS -

 

WARNING:  HIGH CONCENTRATIONS OF OZONE GAS ARE DANGEROUS 

TO HUMANS. LOW CONCENTRATIONS CAN CAUSE IRRITATION TO THE 

EYES, THROAT AND RESPIRATORY SYSTEM. 

 

This  ClearWater  Tech  corona  discharge  ozone 
generator  is  designed  to  operate  under  a  pressure 
condition.    While  safety  precautions  have  been  taken, 
entering  the  equipment  area  should  be  avoided  if  ozone 
gas  is  detected.  Ozone  has  a  very  distinctive  odor  and  is 
detectable  at  very  low  concentrations  (0.02  ppm),  which 
is  far  below  OSHA’s  maximum  permissible  exposure 
level of 0.1 ppm. 
 

 

 
HIGH VOLTAGE -

 

WARNING:  CLEARWATER  TECH  OZONE  GENERATORS  OPERATE 

AT  HIGH  VOLTAGE.  DO  NOT  TAMPER  WITH  OR  DELIBERATELY 

BYPASS  THE  COVER  OR  SAFETY  SWITCHES  BUILT  INTO  THE 

OZONE  GENERATOR  UNLESS  INSTRUCTED  TO  DO  SO  BY  THIS 

MANUAL. IF CONTACT IS MADE WITH OPERATING HIGH VOLTAGE 

COMPONENTS, ELECTRIC SHOCK WILL OCCUR. 

 

 

 

ClearWater  Tech  corona  discharge  ozone  generators  take  line  voltage  and  convert  it  to  48  VDC.  A  high  voltage 
transformer then boosts the voltage. While each ozone generator has a door switch and other safety interlocks, proper care 
must be used by a qualified electrician when making any internal adjustments or performing any maintenance procedures. 
 

 

 

 

 

 

Summary of Contents for CD1500P

































Reviews: