Clavister NetWall W20A Getting Started Manual Download Page 87 | Manualshive

Page: 87 / 89

background image

Appendix E: Apple Mac IP Setup

An Apple Mac can be used as the management computer for initial setup of a Clavister Next
Generation Firewall. To do this, a selected Ethernet interface on the Mac must be configured
correctly with a static IP. The setup steps for this with Mac OS X are:

1.

Go to the Apple Menu and select System Preferences.

2.

Click on Network.

3.

Select Ethernet from the left sidebar menu.

4.

Select Manually in the Configure pull down menu.

87

«
...
85
86
87
88
89
»

Summary of Contents for NetWall W20A


























































































Reviews:

No comments

Related manuals for NetWall W20A

Brand: Parker Pages: 344

BiPAC 4500NZ(L)

Brand: Billion Pages: 146

Brand: H3C Pages: 6

OfficeConnect 3CP4144

Brand: 3Com Pages: 4

OfficeConnect 3CP4144

Brand: 3Com Pages: 2

Brand: H3C Pages: 60

Brand: H3C Pages: 149

Brand: 3Com Pages: 27

Brand: Delta Electronics Pages: 1

Brand: TRENDnet Pages: 2

IE-SW-VL16-14TX-2SC

Brand: Weidmuller Pages: 17

Anybus Communicator ABC4021

Brand: HMS Networks Pages: 60

PCI-6110E/6111E

Brand: National Instruments Pages: 113

8677 - BladeCenter Rack-mountable - Power Supply

Brand: IBM Pages: 126

Brand: Eaton Pages: 14

Brand: ETAS Pages: 82

SW-UNM-24FE2GC-24POE

Brand: Morrell Pages: 8

Brand: ACTi Pages: 14

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands