background image

© 2022

Step 1 of 5

Order #XXXXX

Locked layer contains

placeholder marks.

*

*

When assembled

Item

1

2

3

4

5

6

7

8

9

10

11

12

13

Qty.

1

1

1

1

1

1

1

1

1

1

1

1

2

Steps:

Refer to the Tool-less Frame Assembly general information page.

1) Assemble vertical extrusions [1-2], [3-4], [11-12] & horizontals [5-6-7], [8-9-10]

    together, using 

Tool-less Spline Connectors

 labeled [X] & [Z].

2) Connect vertical assemblies [1/2], [3/4] between horizontal

    assemblies [5/6/7], [8/9/10], using 

Tool-less Corner Connectors

 labeled [A].

3) Install Base Plates [13] to bottom corners of frame assembly

    as shown. See 

Base Plate Attachment

 

detail.

4) Lift frame to upright position, then connect vertical assembly [11/12] between

    horizontal assemblies [5/6/7], [8/9/10] using 

Connection Lock w/ Knob

.

Description

45”h TSP49 Vertical Extrusion

41”h TSP49 Vertical Extrusion

45”h TSP49 Vertical Extrusion

41”h TSP49 Vertical Extrusion

36.166”w TSP49 curved Horizontal Extrusion

36.166”w TSP49 curved Horizontal Extrusion

36.166”w TSP49 curved Horizontal Extrusion

36.166”w TSP49 curved Horizontal Extrusion

36.166”w TSP49 curved Horizontal Extrusion

36.166”w TSP49 curved Horizontal Extrusion

41.209”h Z45 Vertical Extrusion

41.209”h Z45 Vertical Extrusion

6” x 22” Base Plate w/ flange

*

*

1

2

3

4

8

10

12

11

9

13

13

5

6

Connection Lock

w/ Knob

*

BACK VIEW

Knobs face back of assembly.

Tool-less Spline Connector

1. Place extrusions end-to-end.

2. Slide tool-less connectors

    across seam of extrusions.

*

3. Tighten all knobs to secure connection.

Tool-less Corner Connector

1. Slide extrusion onto

    Corner Connector.

2. Tighten all knobs to

    secure connection.

*

Keep corner connectors attached to horizontal extrusions.

Assemble frame flat on ground.

7

1) Place key hole over bolt on panel

    & slide down.

2) Twist knob to secure connection.

Base Plate Attachment

*

bolt

knob

Base Plate

threaded

hole

key hole

FRONT VIEW

A

*

A

*

A

*

A

*

*

X

*

X

*

X

Curved

connector

Curved

connector

Curved

connector

Curved

connector

*

Z

*

Z

*

Z

*

Z

Backwall Frame Assembly

Summary of Contents for SYK-1029












Reviews: