English
GREAT BRITAIN •
customer service
tel:
0845 300 9799
e-mail:
internet:
www.clasohlson.com/uk
Ver
. 20150202
Remote Switch Set
Art.no 18-8881
Model 50027 + 3 × 55005GBX10
36-8836
50027 + 3 × 55001X10
Please read the entire instruction manual before using the product and
then save it for future reference. We reserve the right for any errors in
text or images and any necessary changes made to technical data.
If you have any questions concerning technical problems please
contact our Customer Services.
Safety
• This set of switches is suitable for controlling devices such as lights.
• Make sure that the load device is turned off before connecting it to
the receiver.
• Never connect a load device with a higher power rating than 1000 W.
• These switches are intended for indoor use; do not expose them to
rain or moisture.
3. Each receiver has an indicator in the socket showing which of
the buttons (A, B, or C) it is programmed for. The indicator should
be removed the first time the receiver is used.
If the programming does not work for some reason, the programming
must be re-done. Refer to the
New programming
section.
Operating instructions
Note: Do not touch any of the buttons on the transmitter
before the LED indicator has stopped flashing, otherwise
the programming will change.
1. Plug receiver A into an electrical socket.
2. The LED indicator on the receiver will begin to flash slowly for
30 seconds and then go out.
3. The on/off switching of the socket built into receiver A will now be
controlled by button [ A–ON ] and [ A–OFF ]. The LED indicator on
the receiver will come on when the receiver is switched on and go
out when the receiver is switched off.
4. The other two receivers will be controlled in the same way but with
buttons [ B–ON ], [ B–OFF ] and [ C–ON ], [ C–OFF ] respectively.
5. Buttons [ D–ON ] and [ D–OFF ] are from the outset pre-programmed
to control all three receivers simultaneously.
Note:
Each time a receiver is unplugged from an electrical socket and
plugged in again, it goes into learning mode (the LED indicator flashes
slowly) for 30 seconds.
In learning mode, a channel can be added or several channels can
be removed. All the channels, (A, B, C and D) can be a put on one
receiver if desired. Refer to the
Deleting the programming
and
New
programming
sections.
Deleting the programming
1. Unplug the receiver from the electrical socket.
2. Plug the receiver into an electrical socket after about 10 seconds.
3. The LED indicator on the receiver will flash slowly for 30 seconds
while it is in learning mode.
4. Press the desired [ OFF ] button while the LED indicator is flashing
to delete the programming. The LED indicator will flash quickly
whilst the programming is being deleted.
5. Once programming has been deleted, the receiver is no longer
programmed to any of the buttons on the transmitter.
New programming
The receiver needs to be programmed to one of the buttons A, B, C or
D as follows:
1. Unplug the receiver from the electrical socket.
2. Plug the receiver into an electrical socket after about 10 seconds.
3. The LED indicator on the receiver will flash slowly for 30 seconds
while it is in learning mode.
4. Press [ A–ON ], [ B–ON ], [ C–ON ] or [ D–ON ] whilst the LED indicator
is flashing to programme the receiver to the transmitter.
5. The LED indicator comes on when the programming is completed.
6. Follow the same procedure with the other receivers.
The LED indicator on the receiver shows the status of the receiver in
4 different ways:
• The receiver socket is switched off when the LED indicator is not on.
• The receiver socket is switched on when the LED indicator is on.
• The LED indicator flashes slowly for 30 seconds when the receiver
is in learning mode.
• The LED indicator flashes quickly whilst the programming is being
deleted.
Care and maintenance
• Unplug the mains lead before cleaning the product.
• Clean the product using a soft, moist cloth. Only use mild
detergents; never use solvents or strong, abrasive cleaning agents
for cleaning as these can damage the product.
Disposal
This product should be disposed of in accordance with local regulations.
If you are unsure how to proceed, contact your local council.
Specifications
55001X10 (receiver)
Rated voltage
230 V AC, 50 Hz
Max load
1000 W (4.35 A) resistive load
(incandescent light bulbs, etc)
400 W inductive load
(fluorescent tubes, energy saving bulbs/CFLs, etc.)
50027 (transmitter)
Battery
V23GA, 12 V DC
Frequency
433.92 MHz
Range
up to 25 metres (line-of-sight)
Capable of controlling up to 4 receivers
Transmitter
Receiver
Before use
Inserting the transmitter battery
1. Press the catch on the battery cover in the direction of the arrow
and remove it. Insert the included battery into the transmitter
in accordance with the markings in the battery compartment.
Refit the battery cover.
2. The receivers are already preprogrammed for buttons A, B
and C on the transmitter. Button D controls all three receivers
simultaneously.
