background image

10

Parts & Service: 020 8988 7400 / E-mail: [email protected] or [email protected]

4. If the oil is low, fill the oil reservoir to 

the edge of the oil filler hole.

• We recommend the use of 

10W-SAE30 oil in the engine.

5. Replace the oil filler cap.

CHECKING THE FUEL LEVEL

1. To check the fuel level, remove the fuel tank cap.

2. Just inside the fuel tank is a fuel strainer. Check this filter periodically and 

remove any contaminants which may have accumulated.

3. Refuel in a well-ventilated area 

before starting the engine. If the 
engine has been running, allow it 
to cool. Refuel carefully to avoid 
spilling fuel. Do not fill above the 
fuel strainer shoulder. 

4. After refueling, replace the fuel 

filler cap securely.

RECOMMENDED FUEL

Use unleaded petrol with an octane 
rating of 86 or higher. Do not overfill.

CAUTION: RUNNING THE 
ENGINE WITH INSUFFICIENT OIL 
WILL CAUSE ENGINE DAMAGE.

WARNING: ALWAYS REFUEL IN A WELL VENTILATED AREA AWAY FROM 
ANY SOURCES OF IGNITION AND HEAT.

WARNING: ALLOW THE UNIT TO COOL DOWN BEFORE REFUELLING.

WARNING: DO NOT LEAVE FUEL WITHIN THE REACH OF CHILDREN.

Summary of Contents for Power Wash PLS195A





























Reviews: