background image

4

Parts & Service: 020 8988 7400 / E-mail: [email protected] or [email protected]

GENERAL SAFETY RULES 

1.

NEVER 

direct the spray towards any person or animal.

2.

NEVER 

direct the spray towards electrical wiring or equipment.

3.

NEVER 

hold your finger over the high pressure nozzle.

4.

NEVER 

allow children or untrained personnel to use this machine.

5.

NEVER 

operate the machine with any of the covers removed.

6.

NEVER 

attempt any repairs to this machine. Always refer to your Clarke dealer.

7.

NEVER 

supply any liquid other than water to the water inlet.

8.

NEVER 

use the detergent bottle to introduce flammable liquids/solvents, e.g. paint 

thinners, petrol, oil as there is a risk of explosion.

9.

ALWAYS

 release any residual pressure in the system by turning off the water supply 

and operating the trigger before disconnecting any hose or accessory. 

10.

ALWAYS 

keep the machine itself dry and well clear of water spray.

11.

ALWAYS

 wear protective clothing and safety glasses. Loose particles and other 

debris may be propelled at high speed by the water jet.

12.

ALWAYS

 grip the gun firmly and expect the spray gun to ‘kick’ when starting.

13.

ALWAYS

 respect the requirements of the local water company. Pressure washers may 

only be connected to the mains drinking water supply, if a system separator (also 
known as a backflow preventer) is installed in the supply hose.

14.

ALWAYS 

disconnect from the water supply, and ensure the system is completely 

drained when not in use. Store in a cool dry location.

15.

ONLY

 use chemical cleaning agents (detergents), that are approved for pressure 

washers. CLARKE Traffic Film Remover or CLARKE Wash and WAX (available from your 
dealer), is recommended. 

16.

WARNING

 High pressure water jets can be dangerous if subject to misuse. The jet 

must not be directed at person or anything that they are wearing.

17.

NEVER

 direct the jet at electrical equipment or the machine itself.

18.

WARNING

 High pressure hoses, fittings and couplings are important for the safety of 

the machine. Use only hoses, fittings and couplings recommended by the 
manufacturer.

19.

WARNING

 Water that has flowed through a system separator (also known as a 

backflow preventer) is considered non-drinkable

20.

NEVER 

use the pressure washer if the supply cable or important parts of the machine 

are damaged.

WARNING: Water at high pressure can be dangerous and can cause 
damage if the operator is careless. Never allow anyone to operate this 
pressure washer unless they are familiar with the safety precautions.

Summary of Contents for JETSTAR 1750





















Reviews: