Clarke 7623071 Operation & Maintenance Instructions Manual Download Page 3

3

SAFETY PRECAUTIONS

1. This jack is for lifting only. Do not move a load using the jack as a dolly.

2. Do not use to lift people.

3. Always inspect the jack before use. Make sure that all parts are in good 

condition and operating smoothly, and that no cracks or distortion is 
apparent. If in doubt do not use. Have the damaged parts replaced or 
consult your CLARKE dealer.

4. Make sure that the jack is on a firm level base, and there is no possibility of 

it slipping when under load.

5. Make sure the load is taken by the full saddle and that the point of lift on 

the load, is strong enough to support the load adequately.

6. Do not work under the raised vehicle until it is supported by suitable means 

e.g. axle stands, NEVER rely on the jack to support the vehicle by itself.

7. Never push a load off the jack.

8. Ensure that all personnel are well clear of a load being raised or lowered.

9. Do not try to lift more then the rated load for the jack.

10. Do not use the jack if an oil leak is apparent. Consult your Clarke dealer.

11. Consult the vehicle handbook to determine the correct lifting points.

12. Always watch the jack and the load during operation.

13. Check the condition of the labels regularly and replace as required.

14. The jack must be maintained and repaired by suitably qualified persons.

15. Do not make any modifications to this jack or adjust any valves.

ENVIRONMENTAL PROTECTION

One of the most damaging sources of environmental pollution is oil products. 
Never throw away used hydraulic oil with domestic refuse or flush it down a 
sink or drain. Collect any hydraulic oil in a leak proof container and take it to 
your local waste disposal site.

If disposing of this product or any damaged components, do not dispose of 
with general waste. This product contains valuable raw materials and should 
be taken to your local civic amenity site for recycling of metal products.

WARNING: THE OPERATOR MUST FOLLOW ALL INSTRUCTIONS WITHIN THIS 
INSTRUCTION BOOKLET

Summary of Contents for 7623071













Reviews: