background image

18

Parts & Service: 020 8988 7400 / E-mail: [email protected] or [email protected]

STORAGE

1. Disconnect the high pressure hose and drain all water from the hose.

2. Coil the hose and store the gun/lance in the holders located on the side 

frame of the pressure washer.

STORAGE PROCEDURE

Make sure that the pressure washer has been thoroughly cleaned before 
storing it in a clean dry place. For long term storage See page 20.

MAINTENANCE

CLEANING THE NOZZLE

1. Switch off the pressure washer and the water supply.

2. Pull the trigger to release any water pressure.

3. Disconnect the lance from the gun assembly.

4. Remove all blockages with the 

nozzle cleaning tool provided and 
back flush with clean water.

5. Run water into the end of the 

lance for 30 seconds to back flush 
loose particles.

6. Reconnect the lance to the gun 

assembly and turn on the water 
supply.

CLEANING THE WATER INLET FILTER

1. Remove the filter from the water 

inlet of the pump as shown.

2. Clean the filter by flushing both 

sides with water.

3. Replace the filter into the water 

inlet.

• Do not operate without the 

filter properly installed.

Summary of Contents for 7320212





























Reviews: