Clarke 723100 Operation & Maintenance Instructions Manual Download Page 3

3

Parts & Service: 020 8988 7400 / E-mail: [email protected] or [email protected]

 SAFETY INSTRUCTIONS

GENERAL

1. Read all instructions before use 

and save these instructions for 
future use.

2. An approved residual current 

device (RCD) which has a 
tripping current of less then 30mA 

MUST

 be used for all operations.

3. The electrical supply must be the 

same as that on the rating plate.

4. Always make sure that your 

hands are dry when connecting 
or disconnecting from the mains 
supply.

5. Never pull the mains lead to 

disconnect the pump from the 
mains socket.

6. The mains plug must be kept 

away from the water at all times.

7. Do not allow children or 

unauthorised people to touch the 
pump, cables or connections.

8. Disconnect the pump from the 

mains supply when not in use.

9. If necessary have the pump 

repaired by a qualified person.

10. Keep the mains lead away from 

heat, oil and sharp edges.

11. If you have to use an extension 

lead with this product, it must be 
designed for outdoor use and 
incorporate a cable suitable for 
use with Class I appliances.

12. Disconnect the pump from the 

electrical supply and wear gloves 
during servicing or maintenance.

PUMP SPECIFIC

1. Do not pump explosive / 

flammable liquids or chemicals.

2. Never allow the pump to run dry 

or operate out of the water.

3. Submersible pumps should always 

be submerged and stored 
vertically.

4. Disconnect the pump from the 

mains supply before placing it 
into or removing it from the water.

5. Always check the plug, and all 

cables for damage before use.

6. Do not use the pump if 

damaged. Refer to qualified 
service personnel for repair.

7. Never carry or lower the pump by 

the power cable or float switch 
always use the handle or a rope 
tied securely to the handle.

8. Never insert your fingers into the 

pump whilst it is connected to the 
mains.

9. Never use the submersible pump 

in a swimming pool when there 
are people or animals in the pool.

10. Keep the pump clear of any 

sediment by standing it on a 
platform or brick or suspending it 
at a suitable depth.

11. Do not use the pump if the water 

is liable to freeze, as this can 
cause damage to the pump. 
Remove the pump from the 
water and store it in a frost free 
location.

Summary of Contents for 723100













Reviews: