12
EN
DSX Touch
Mounting the wall bracket
• Before attaching the wall bracket to the wall, ensure that the remote control has radio con-
tact to the instantaneous water heater from its designated position.
• The wall bracket of the remote control can either be attached securely with the included
adhesive tape, after stripping off the protection film (as shown in the figure B1), on a rigid
board (e.g. tile) or with suitable dowels (Ø 4 mm) and screws (as shown in the figure B2).
• When mounting with adhesive tape, ensure that the mounting surface is dry and free of
grease and soap.
• When using the adhesive tape it is not possible to further adjust the position because of
the strong adherence of the glue. Therefore, pay attention to a horizontal alignment when
attaching it.
• The remote control is magnetically retained at the wall bracket.
• Keep the remote control and wall bracket away from credit cards or other cards with mag-
netic strips. The built in magnets can damage the card’s magnetic strip.
Initial operation
By the time the power settings have been carried out and the power supply to the instantaneous
water heater is enabled, insert the batteries into the remote control.
New registration of remote control at the instant water heater
1. Make sure that the power supply to the instantaneous water heater is switched on (fuse).
2. Remove the batteries until the display expires. After inserting the batteries, the display indi-
cates all symbols for about 4 seconds.
3. The remote control connects to the appliance automatically and the display switches to the
setpoint value display.
In the case of an unsuccessful registration the display indicates “
bt
” after 45 seconds. The
remote control quits the registration process and switches to standby mode. By pressing a key
the registration process will be repeated.
Notes:
• With no remote control registered or without working radio connection, the instantaneous
water heater heats to the prior selected set temperature.
Handling
The remote control is equipped with the following functions:
1. Arrow buttons
You can set the required temperature gradually to a lower or higher value using the arrow two
buttons and .
Note: If the temperature display is set to “
--
” with arrow button , the instantaneous water
heater switches off the heating function.
2. Programme buttons
The two programme buttons and allow to quickly select the preset temperature without
the need to press the and buttons several times.
The factory setting for programme is 35 °C and for programme it is 48 °C. You can assign
your own settings for the programme buttons:
3. Remote control
Technical data
Model
FX 3 Remote control
Operating voltage
3 V
Type of battery
2x AAA Alkaline
1)
Type of protection
IP 20
Transmission range
10 metres incl. barrier
Transmission power
< 8 mW
Transmission and receiving frequency range
2.4 – 2.4385 GHz
Radiation
undirected
Approvals
Europe EN 300 328 / CE
1) Do not use rechargeable batteries.
1. Select the desired temperature with and .
2. To save the current temperature, press the programme button
or
for min. two
seconds.
Safety notes
• At malfunction of the remote control remove the batteries immediately.
• Do not expose the remote control to moisture.
• Flat batteries can leak and damage the remote control. Hence, replace flat batteries right
away as soon as battery symbol lights up in the display or the remote control does not
response after keystroke.
• When the remote control is not to be used in the long term, remove the batteries.
• Without working radio connection, the appliance heats to the prior selected set value.
Battery replacement
Replace the batteries with new AAA-batteries when the battery symbol flashes up.
• Do not use rechargeable batteries!
• Non-rechargeable batteries are not to be recharged.
• Different types of batteries or new and used batteries are not to be mixed.
• When replacing the batteries, observe the correct polarity.
Disposal
Batteries may contain environmentally hazardous substances. Therefore, used
batteries must be disposed of at special collecting points and not be mixed with
general household waste.
At the end of the remote control’s lifetime, the batteries must be disposed of separate from the
appliance.
Note: FX 3 Displayed informations and app Smart Control
For further informations please use the online operation and installation
instruction. Please follow the link below or use the QR code via smart-
phone or tablet.
https://www.clage.de/links/gma/DSX-Touch-GMA-9120-34385
