manualshive.com logo in svg

Citrix ByteMobile T1010, Installation, Configuration And Administration

Share
Download
Citrix ByteMobile T1010 Installation, Configuration And Administration Download Page 61

T-Series Traffic Director Installation, Configuration and Administration Guide

2-21

Connecting and Disconnecting AC Power

Connecting an AC Shelf to Power

The T1000 with AC option has two AC-power C20 input connectors. Two (2x) C20/C19 
type AC jumper cords are supplied with the AC power unit. To supply power to the T1000 
unit, connect one end of each power cord to a power connector on the rear of the T1000 and 
the other end of each power cord to a 120-240 volt 20 amp power distribution unit or 
appropriate electrical outlet. Use a regulating uninterruptible power supply (UPS) to protect 
the T1000 from power surges and voltage spikes, and to keep the T1000 operating in case of 
power failure. See the following figure.

Figure 2-8

Connecting AC Power

Use the following procedure to connect the AC shelf to power:

Step 1

Isolate the power supply to ensure that the power supply cables are not energized. Use an 
appropriate lockout/tagout procedure to ensure that the power supply cables are not 
accidentally energized during the installation procedure.

Step 2

Connect the power cables to both power connectors.

Summary of Contents for ByteMobile T1010













































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands