Citizen CD-S500 series User Manual Download Page 6 | Manualshive

Page: 6 / 52

background image

6

Important Safety Instructions

•

Read all of these instructions and save them for later reference.

•

Follow all warnings and instructions marked on the product.

•

Unplug this product from the wall outlet before cleaning. Do not use liquid or aerosol
cleaners. Use a damp cloth for cleaning.

•

Do not use this product near water.

•

Do not place this product on an unstable cart, stand or table. The product may fall,
causing serious damage to the product.

•

Slots and openings on the cabinet and the back or bottom are provided for ventilation.
To ensure reliable operation of the product and to protect it from overheating, do
not block or cover these openings. The openings should never be blocked by placing
the product on a bed, sofa, rug or other similar surface. This product should never
be placed near or over a radiator or heat register. This product should not be placed
in a built-in installation unless proper ventilation is provided.

•

This product should be operated from the type of power source indicated on the
marking label.
If you are not sure of the type of power available, consult your dealer or local power
company.

•

This product is equipped with a three-pronged plug, a plug having a third (grounding)
pin. This plug will only fit into a grounding-type power outlet. This is a safety feature.
If you are unable to insert the plug into the outlet, contact your electrician to replace
your obsolete outlet. Do not defeat the safety purpose of the grounding-type plug.

•

Do not allow anything to rest on the power cord. Do not locate this product where
the cord will be walked on.

•

If an extension cord is used with this product, make sure that the total of the ampere
ratings on the products plugged into the extension cord do not exceed the extension
cord ampere rating. Also, make sure that the total of all products plugged into the
wall outlet does not exceed 15 amperes for 120V outlet and 7.5 amperes for 220V-
240V outlet.

•

Never push objects of any kind into this product through cabinet slots as they may
touch dangerous voltage points or short out parts that could result in a risk of fire or
electric shock. Never spill liquid of any kind on the product.

•

Except as explained elsewhere in this manual, don't attempt to service this product
yourself. Opening and removing those covers that are marked "Do Not Remove" may
expose you to dangerous voltage points or other risks. Refer all servicing on those
compartments to service personnel.

«
...
4
5
6
7
8
...
»

Summary of Contents for CD-S500 series





















































Reviews:

No comments

Related manuals for CD-S500 series

NEFAX - 691 B/W Laser

Brand: NEC Pages: 20

Brand: 3D Systems Pages: 26

Brand: 3D Systems Pages: 39

WorkSeries 200 Series

Brand: 3D Platform Pages: 9

Brand: TallyGenicom Pages: 92

Brand: Samsung Pages: 134

Brand: Felix printers Pages: 28

16C0365 - 5500 MFP

Brand: Lexmark Pages: 88

Brand: Konica Minolta Pages: 44

Brand: Xerox Pages: 214

Brand: Cardco Pages: 28

WorkCentre Pro 416

Brand: Xerox Pages: 470

ScreenWriter Colour ScreenWriter

Brand: Xante Pages: 446

Brand: idp Pages: 63

Brand: Ricoh Pages: 2

Brand: Kyocera Pages: 392

Aficio SP 320 Series

Brand: Ricoh Pages: 272

Brand: SIGN RACER Pages: 73

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands