Citizen CD-S500 series User Manual Download Page 18

Page: 18 / 52

Chapter2

Names and Functions of Parts

Operation Panel

POWER LED (Green)

It is lit when the power is supplied. When
maintenance mode is set or there is an
error indication, it is either lit or flashing.

PAPER OUT LED (Orange)

It is lit in paper out status. When
maintenance mode is set or there is an
error indication, it is either lit or flashing.

ERROR LED (Orange)

It is lit when the rear cover or front cover
is open. When maintenance mode is set
or there is an error indication, it is either
lit or flashing.

FEED Switch

When this switch is pressed once, paper
feeds (1 line). If it is held down, paper
feeds continuously until it is released.
And when there is a printer error, pressing
this switch can cancel the error status.

Summary of Contents for CD-S500 series





















































Search results

Summary of Contents for CD-S500 series

Reviews:

Related manuals for CD-S500 series

Brands by name

Popular brands

Citizen CD-S500 series, User Manual

Search results

Summary of Contents for CD-S500 series

Reviews:

Related manuals for CD-S500 series

Brands by name

Popular brands