Cisco XR 1200 series Command Reference Manual Download Page 368

Page: 368 / 432

hw-module logging onboard

To disable onboard failure logging (OBFL), use the

hw-module logging onboard

command in administration

configuration mode. To enable OBFL again, use the

form of this command.

hw-module

{

all

subslot node-id

}

logging onboard

[

disable

severity

{

alerts| emergencies

}]

no hw-module

{

all

subslot node-id

}

logging onboard [disable]

Syntax Description

Enables or disables OBFL for all nodes.

all

Enables or disables OBFL for the designated node. The

node-id

argument is

entered in the

rack/slot/module

notation.

subslot node-id

Enables or disables OBFL. See the Usage Guidelines for more information.

disable

(Optional) Specifies the severity level for the syslog message that is logged into
the OBFL storage device.

severity

Specifies that both emergency and alert syslog messages are logged. The default
is the

alerts

keyword.

alerts

Specifies that only the emergency syslog messages are logged.

emergencies

Command Default

By default, OBFL logging is enabled.

severity

: 1 (alerts) and 0 (emergencies)

Command Modes

Administration configuration

Command History

Modification

Release

This command was introduced.

Release 3.4.1

Usage Guidelines

Use the

hw-module logging onboard

command to enable or disable OBFL.

•

To disable OBFL use the

disable

keyword. OBFL is enabled by default.

hw-module

{

all

subslot node-id

}

logging onboard disable

•

To enable OBFL, use the

form of the

hw-module logging onboard

command with the

disable

keyword. OBFL is enabled by default. Use this command only if you disabled OBFL:

no hw-module

{

all

subslot node-id

}

logging onboard disable

Cisco IOS XR System Monitoring Command Reference for the Cisco XR 12000 Series Router, Release 4.1

356

OL-24735-01

Onboard Failure Logging Commands

hw-module logging onboard

Summary of Contents for XR 1200 series

















































































































































































































































































































































































































































Search results

Summary of Contents for XR 1200 series

Reviews:

Related manuals for XR 1200 series

Brands by name

Popular brands

Cisco XR 1200 series, Command Reference Manual

Search results

Summary of Contents for XR 1200 series

Reviews:

Related manuals for XR 1200 series

Brands by name

Popular brands