Cisco XR 1200 series Command Reference Manual Download Page 264

Page: 264 / 432

source port

To identify the port of the source device, use the

source port

command in the appropriate configuration mode.

To use the unused port number, use the

form of this command.

source port port

no source port

Syntax Description

Identifies the port number of the source device. Range is 1 to 65535.

port port

Command Default

IP SLA uses an unused port that is allocated by system.

Command History

Modification

Releas

This command was introduced.

Release 3.3.0

Usage Guidelines

The

source port

command is not supported to configure ICMP operations; it is supported only to configure

UDP operations.

Task ID

Operations

Task ID

read, write

monitor

Examples

The following example shows how to designate a port for the

source port

command in IP SLA UDP jitter

configuration mode:

RP/0/0/CPU0:router#

configure

RP/0/0/CPU0:router(config)#

ipsla

RP/0/0/CPU0:router(config-ipsla)#

operation 1

RP/0/0/CPU0:router(config-ipsla-op)#

type udp jitter

RP/0/0/CPU0:router(config-ipsla-udp-jitter)#

source port 11111

Related Commands

Description

Command

Configures an IP SLA operation.

operation, on page 174

Schedules an IP SLA operation.

schedule operation, on page 215

Cisco IOS XR System Monitoring Command Reference for the Cisco XR 12000 Series Router, Release 4.1

252

OL-24735-01

IP Service Level Agreement Commands

source port

Summary of Contents for XR 1200 series

















































































































































































































































































































































































































































Search results

Summary of Contents for XR 1200 series

Reviews:

Related manuals for XR 1200 series

Brands by name

Popular brands

Cisco XR 1200 series, Command Reference Manual

Search results

Summary of Contents for XR 1200 series

Reviews:

Related manuals for XR 1200 series

Brands by name

Popular brands