Cisco WRT300N User Manual Download Page 2 | Manualshive

Page: 2 / 92

Cisco WRT300N User Manual Download Page 2

Wireless-N Broadband Router

Copyright and Trademarks

Specifications are subject to change without notice. Linksys is a registered trademark or trademark of Cisco
Systems, Inc. and/or its affiliates in the U.S. and certain other countries. Copyright © 2007 Cisco Systems, Inc. All
rights reserved. Other brands and product names are trademarks or registered trademarks of their respective
holders.

How to Use This User Guide

This User Guide has been designed to make understanding networking with the Wireless-N Broadband Router
easier than ever. Look for the following items when reading this User Guide:

In addition to these symbols, there are definitions for technical terms that are presented like this:

Also, each figure (diagram, screenshot, or other image) is provided with a figure number and description, like
this:

Figure numbers and descriptions can also be found in the “List of Figures” section in the “Table of Contents”.

This exclamation point means there is a caution or warning
and is something that could damage your property or the
Wireless-N Broadband Router.

This checkmark means there is a note of interest and is
something you should pay special attention to while using
the Wireless-N Broadband Router.

This question mark provides you with a reminder about
something you might need to do while using the Wireless-N
Broadband Router.

word:

definition.

Figure 0-1: Sample Figure Description

WRT300N v1.1-UG-70118 NC DF

WARNING:

This product contains chemicals, including lead, known

to the State of California to cause cancer, and birth defects or other
reproductive harm.

Wash hands after handling.

«
1
2
3
4
...
»

Summary of Contents for WRT300N





























































































Reviews:

No comments